Cisco 819 series Скачать руководство пользователя

Страница: 81 / 84

A-5

Cisco 819 Integrated Services Router Hardware Installation Guide

OL-23125-02

Appendix A Technical Specifications

Mean Time Between Failure Ground Benign Environment

Table A-2

lists the Mean Time Between Failire (MTBF) values for Cisco 819 ISRs. The MTBF is

calculated based on the Ground Benign condition. The values may be adjusted based on the different
router usage.

Antenna (Diversity and Antenna 3G-ANTM1919D)

Antenna Dimensions

7.63 x 0.94 x 0.63 in (19.38 x 2.39 x 1.60 cm)

Frequency Range

806 to 960 MHz and 1710 to 2170 MHz

Gain

0 decibels relative to isotropic (dBi) (806 to 960 MHz) and 0 dBi (1710 to 2170 MHz)

Maximum Power

25 W

Connector

TNC male

Voltage Standing Wave
Ratio

< 2.5:1

Nominal Impedance

50 ohms

AC Power Adapter is not IP 41 rated. Installation must include protection of the adapter and power plug from water.

Contact Martek Power directly for details.

Table A-1

Cisco 819 ISR Specifications (continued)

Description

Hardened Design
Specification

(Cisco 819HG and Cisco
819HG-4G ISRs)

Non-Hardened Design
Specifications

(Cisco 819G and Cisco
819G-4G ISRs)

Hardened Design Specifications

(C819HGW and C819HWD ISRs)

Table A-2

MTBF Values

SKUs

MTBF (hours)

Cisco 819HG and Cisco 819G ISRs

C819HG-U-K9

C819G-U-K9

380,000

7-A-K9

7-K9

C819G+7-A-K9

C819G+7-K9

420, 000

C819HG-S-K9

C819HG-V-K9

C819HG-B-K9

C819G-S-K9

C819G-V-K9

C819G-B-K9

280, 000

Содержание 819 series





















































































Результаты поиска

Содержание 819 series

Отзывы:

Похожие инструкции для 819 series

Бренды по названию

Популярные бренды

Cisco 819 series, Руководство по установке

Результаты поиска

Содержание 819 series

Отзывы:

Похожие инструкции для 819 series

Бренды по названию

Популярные бренды