Cisco 7600-SIP-400 - SPA Interface Processor 400 Скачать руководство пользователя страница 69 | Manualshive

Страница: 69 / 172

Cisco 7600-SIP-400 - SPA Interface Processor 400 Скачать руководство пользователя страница 69

3-23

Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide

OL-5052-14

Chapter 3 Overview: Cisco 7600 Series Router Shared Port Adapters

1-Port OC-12c/STM-4 ATM SPA Overview

Figure 3-17

SFP Optics Module

The SFP optical transceiver modules used with the POS SPAs provide the following optical fiber options:

•

Multimode—155-Mbps, OC-3c/STM-1 optical fiber (SONET STS-3c or SDH STM-1)

Use a multimode optical fiber that has a core/cladding diameter of 62.5/125 microns.

•

Single-mode—155-Mbps, OC-3c/STM-1 optical fiber (SONET STS-3c or SDH STM-1)

Use a single-mode optical fiber that has a modal-field diameter of 8.7 ±0.5 microns. (Nominal
diameter is approximately 10/125 microns.)

For single-mode and multimode optical fiber connections, you can use either a duplex LC-type cable or
two simplex LC-type cables, one for transmit (TX) and one for receive (RX).

Use single-mode (for intermediate- or long-reach configurations) or multimode optical fiber cable to
connect your router to a network or to connect two OC-3c/STM-1-equipped routers back to back.

Long-range SFP optical transceiver modules (for long-reach configurations) cannot be connected
back-to-back without using an attenuator between the two of them.

Figure 3-18

LC Type Cables

1-Port OC-12c/STM-4 ATM SPA Overview

The following sections describe the 1-Port Channelized OC-12/STM-4 SPA:

•

1-Port Channelized OC-12/STM-4 SPA LEDs, page 3-24

•

1-Port Channelized OC-12/STM-4 SPA Interface Specifications, page 3-24

•

1-Port Channelized OC-12/STM-4 SPA Cables and Connectors, page 3-25

127158

/ /

/ /

/ /

TX

RX

84929

«
...
67
68
69
70
71
...
»

Содержание 7600-SIP-400 - SPA Interface Processor 400













































































































































































Отзывы:

Нет отзывов