Cisco 7600-SIP-400 - SPA Interface Processor 400 Скачать руководство пользователя страница 11

Страница: 11 / 172

Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide

OL-5052-14

Preface

Document Revision History

12.2 (33) SRD

OL-5052-10

July 2008

•

Added support for BX-SFP, DWDM-SFP,
DWDM-XFP and CWDM-SFP modules
for features 8731-1, 8767-1, 8768-1,
8769-1and 8730-1 in

Supported BX SFP

Modules

Supported DWDM-XFP

Modules

and

Supported DWDM-SFP

Modules

and

Supported CWDM-SFP

Modules

, Chapter 1

•

Added Support for 4-Port Fast Ethernet
SPA and 8-Port Fast Ethernet SPA on
SIP-400 in -

Table 1-2SIP and SPA

Compatibility Table for Ethernet SPAs

•

Updated Chapter 4, Preparing to Install a
SIP or a Shared Port Adapter, section

Required Tools and Equipment

to add

Torque specification

•

Updated Chapter 6, Installing and
Removing a Shared Port Adaptor, section

SIP Installation and Removal

, Step 5

•

Added Chapter 6, Section

Installing a SPA

in a SIP

, Step 4 and caution note at the

same location.

12.2(33)SRC1

OL-5052-09

May 2008

•

Added support for DWDM-XFP modules
in

Supported DWDM-XFP Modules

Chapter 1

12.2(33)SRC

OL-5052-08

•

Added SFP-GE-T support

•

Added the following SPA support to the
SIP-400:

–

SPA-1X10GE-L-V2

–

SPA-2XCT3/DS0

–

SPA-4XCT3/DS0

–

SPA-2XT3/E3

–

SPA-4XT3/E3

–

SPA-8XCHT1/E1

–

SPA-2CHT3-CE-ATM

–

SPA-1XCHSTM1/OC3

—

OL-5052-07A

June 2007

Added cabling information for the 24-Port
Channelized T1/E1 ATM CEoP SPA.

12.2(33)SRB1

OL-5052-07

June 2007

Added support for XFP-10GZR-OC192LR.

12.2(33)SRB

OL-5052-06

February
2006

Added support for the 1-Port Channelized
OC-3 STM1 ATM CEoP SPA and 24-Port
Channelized T1/E1 ATM CEoP SPA.

Table 1

Document Revision History

Содержание 7600-SIP-400 - SPA Interface Processor 400













































































































































































Результаты поиска

Содержание 7600-SIP-400 - SPA Interface Processor 400

Отзывы:

Cisco 7600-SIP-400 - SPA Interface Processor 400, Руководство по установке оборудования, Страница: 11 / 172

Результаты поиска

Содержание 7600-SIP-400 - SPA Interface Processor 400

Отзывы: