Cisco 7600-SIP-400 - SPA Interface Processor 400 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 172

Cisco 7600-SIP-400 - SPA Interface Processor 400 Скачать руководство пользователя страница 12

xii

Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide

OL-5052-14

Preface

Organization

Organization

This document contains the following chapters:

12.2(33)SRA

OL-5052-05

June 2006

Added support for 1-Port OC-48c/STM-16
POS SPA, 1-Port Channelized STM-1/OC-3
SPA , 4-Port and 8-Port Fast Ethernet SPA, and
2-Port and 4-Port OC-48c/STM-16 POS SPA.

12.2(18)SXF2

OL-5052-04

January
2006

Added support for 1-Port OC-192c/STM-64
POS/RPR VSR Optics SPA.

12.2(18)SXF

OL-5052-03

September
2005

Added support for Cisco 7600 SIP-600, 1-Port
OC-192c/STM-64 POS/RPR SPA, 1-Port
OC-48c/STM-16 ATM SPA, 1-Port 10-Gigabit
Ethernet SPA, 5-Port Gigabit Ethernet SPA,
2-Port Gigabit Ethernet SPA and 1-Port
OC-48c/STM-16 ATM SPA, and 1-Port
OC-192c/STM-64 POS/RPR XFP SPA.

12.2(18)SXE2

OL-5052-02

June 2005

Added support for IPSec VPN SPA, and
Cisco 7600 SSC-400.

12.2(18)SXE

OL-5052-01

April 2005

First release.

Table 1

Document Revision History

Chapter

Title

Description

Chapter 1

SIP and SPA Product Overview

Provides an introduction to SPA interface
processors (SIPs) and shared port adapters (SPAs).

Chapter 2

Overview: Cisco 7600 Series SIPs

Provides a SIP/SPA compatibility summary. For
each supported SIP, provides a summary of SIP
characteristics and a SIP overview.

Chapter 3

Overview: Cisco 7600 Series
Router Shared Port Adapters

For each supported SPA, provides a summary of
SPA characteristics and a SPA overview.

Chapter 4

Preparing to Install a SIP or a
Shared Port Adapter

Describes the required tools, equipment, and safety
guidelines for installing SIPs and SPAs

Chapter 5

Installing and Removing a SIP

Describes the procedures for installing and
removing a SIP on a Cisco 7600 series router.

Chapter 6

Installing and Removing a Shared
Port Adapter

Describes the procedures for installing and
removing a SPA on a Cisco 7600 series router. It
also describes how to verify the SIP and SPA
installation.

Chapter 7

Troubleshooting the Installation

Provides information for troubleshooting the
installation of SIPs and SPAs. It also describes
helpful debug commands and error messages.

«
...
10
11
12
13
14
...
»

Содержание 7600-SIP-400 - SPA Interface Processor 400













































































































































































Отзывы:

Нет отзывов