Cisco 450 Скачать руководство пользователя страница 27

Страница: 27 / 36

C H A P T E R

Powering On the Cisco VG450 Voice Gateway

To power on your Cisco VG450 Voice Gateway, perform the following tasks in the order listed, as required:

•

Checklist for Power-On, on page 25

•

Power-On Procedure, on page 25

•

Troubleshooting, on page 27

Checklist for Power-On

You can power on a Cisco VG450 Voice Gateway if it meets the requirements described in Chapter 3: Installing
the Cisco VG450 Voice Gateway.

• The chassis is securely mounted.

• Power cable is connected.

• Interface cables are connected.

Power-On Procedure

Perform this procedure to power on your Cisco VG450 Voice Gateway, and verify that it goes through its
initialization and self-test. When this is finished, the Cisco VG450 Voice Gateway is ready to configure.

This unit might have more than one power supply connection. All connections must be removed to de-energize
the unit. Statement 1028

Danger

Installation of the equipment must comply with local and national electrical codes. Statement 1074

Danger

To power on the Cisco VG450 Voice Gateway, perform the following:

SUMMARY STEPS

Power on your terminal or PC, and configure it for 9600 bps, 8 data bits, 1 stop bit, and no parity.

Cisco 450 Voice Gateway Hardware Installation Guide

Содержание 450




































Результаты поиска

Содержание 450

Отзывы:

Похожие инструкции для 450

Бренды по названию

Популярные бренды

Cisco 450, Руководство по установке оборудования

Результаты поиска

Содержание 450

Отзывы:

Похожие инструкции для 450

Бренды по названию

Популярные бренды