Cisco 2801 - Integrated Services Router Скачать руководство пользователя страница 80

Страница: 80 / 204

Chassis Installation Procedures for Cisco 2800 Series Routers

OL-5786-03

Setting Up the Chassis

Figure 10

Bracket Installation for Rear Mounting

Figure 11

Bracket Installation for Center Mounting with Front Panel Forward

Installing the Router in a Rack

After you have attached the brackets to the router chassis, use the screws provided with the rack to install
the chassis in the rack. (See

Figure 12

Tip

Start the lower pair of screws first, and rest the brackets on the lower screws while you insert the upper
pair of screws.

Tip

The screw slots in the brackets are spaced to line up with every

second

pair of screw holes in the rack.

When the correct screw holes are used, the small threaded holes in the brackets line up with unused screw
holes in the rack. If the small holes do not line up with the rack holes, you must raise or lower the
brackets to the next rack hole.

95747

Bracket

for 23-inch rack

Bracket

for 19-inch rack

Use four screws on each side.

Bracket

for 19-inch rack

Bracket

for 23-inch rack

A= ACT

FE 0/1

PVDM2

PVDM1

PVDM0

AIM1

AIM0

FE 0/0

S= SPEED

A= FDX
A= LINK

95746

Bracket

for 23-inch rack

Use four screws on each side.

Do Not Remo

ve During Netw

ork Operatio

COMPACT F

LASH

OPTIONAL R

PS INPUT

SYS

PWR

AUX/

PWR

SYS

ACT

12V 1

100-240 V~ 3

50/60 Hz

CONSOLE

AUX

Bracket

for 19-inch rack

Bracket

for 23-inch rack

Bracket

for 19-inch rack

Содержание 2801 - Integrated Services Router













































































































































































































Результаты поиска

Содержание 2801 - Integrated Services Router

Отзывы:

Похожие инструкции для 2801 - Integrated Services Router

Бренды по названию

Популярные бренды

Cisco 2801 - Integrated Services Router, Руководство пользователя

Результаты поиска

Содержание 2801 - Integrated Services Router

Отзывы:

Похожие инструкции для 2801 - Integrated Services Router

Бренды по названию

Популярные бренды