Cisco 2801 - Integrated Services Router Скачать руководство пользователя страница 79

Страница: 79 / 204

Chassis Installation Procedures for Cisco 2800 Series Routers

OL-5786-03

Setting Up the Chassis

Attaching Rack-Mount Brackets to Cisco 2801 Routers

Use four of the supplied number-8 Phillips flat-head screws to attach the long side of each bracket to the
router.

Figure 8

shows how to attach the brackets to the sides of the router with the front panel forward.

Figure 8

Attaching Rack-Mounting Brackets to a Cisco 2801 Router

Attaching Rack-Mount Brackets to Cisco 2811, Cisco 2821, and Cisco 2851 Routers

Attach the mounting brackets to the router chassis as shown in

Figure 9

through

Figure 11

, using the

screws provided.

Caution

Do not overtorque the screws. The recommended torque is 15–18 inch-lb (1.7–2.0 N-m).

Attach the second bracket to the opposite side of the chassis. Use a number 2 Phillips screwdriver to
install the bracket screws.

Caution

Your chassis installation must allow unrestricted airflow for chassis cooling.

Figure 9

Bracket Installation for Front Mounting

95770

95745

Bracket

for 23-inch rack

Bracket

for 19-inch rack

Bracket

for 19-inch rack

Bracket

for 23-inch rack

Use four screws on each side.

Do Not Remo

ve During Netw

ork Operatio

COMPACT F

LASH

OPTIONAL R

PS INPUT

SYS

PWR

AUX/

PWR

SYS

ACT

12V 1

100-240 V~ 3

50/60 Hz

CONSOLE

AUX

Содержание 2801 - Integrated Services Router













































































































































































































Результаты поиска

Содержание 2801 - Integrated Services Router

Отзывы:

Похожие инструкции для 2801 - Integrated Services Router

Бренды по названию

Популярные бренды

Cisco 2801 - Integrated Services Router, Руководство пользователя

Результаты поиска

Содержание 2801 - Integrated Services Router

Отзывы:

Похожие инструкции для 2801 - Integrated Services Router

Бренды по названию

Популярные бренды