Cisco 2801 - Integrated Services Router Скачать руководство пользователя страница 38

Страница: 38 / 204

Overview of Cisco 2800 Series Routers

OL-5783-01

Hardware Features

To see descriptions of LEDs in removable modules and interface cards, refer to the applicable
documentation for those products: the

Cisco Network Modules Hardware Installation Guide

or the

Cisco

Interface Cards Installation Guide

For LED troubleshooting information, including possible trouble causes and corrective actions, see

Table 1

in the

“Troubleshooting Cisco 2800 Series Routers”

document.

Table 5

Summary of Cisco 2801 Series LED Indicators

LED

Color

Description

Location

SYS PWR

Green

Router has successfully booted up and the

software is functional. This LED blinks while

booting or in the ROM monitor.

Front

SYS ACT

Green

Blinking when any packets are transmitted or received
on any WAN or LAN or system is monitoring internal
activities.

Front

Green

On when flash memory is busy. Do not

remove the CompactFlash memory card when this
light is on.

Front

AUX/PWR

Green/

Amber

Indicates that the inline power supply is present

(LED is on). When the inline power supply is not

installed, the LED is off. If the power supply is

working properly, the LED is green. If the

power supply is not working properly, the LED

is amber, indicating an inline power failure.

Front

FE 0 Link

Green

On when the router is correctly connected to a

local Ethernet LAN through Ethernet port 0.

Front

FE 0 100

Green

On indicates a 100-Mbps link.

Off indicates a 10-Mbps link.

Front

FE 0 FDX

Green

On indicates full-duplex operation.

Off indicates half-duplex operation.

Front

FE 1 Link

Green

On when the router is correctly connected to a

local Ethernet LAN through Ethernet port 1.

Front

FE 1 100

Green

On indicates a 100-Mbps link.

Off indicates a 10-Mbps link.

Front

FE 1 FDX

Green

On indicates full-duplex operation.

Off indicates half-duplex operation.

Front

AIM 0

Green

On indicates presence of an advanced integration

module (AIM) in AIM slot 0.

Front

AIM 1

Green

On indicates presence of an AIM in AIM slot 1.

Front

PVDM 0

Green

On indicates presence of a packet voice data

module (PVDM) in PVDM slot 0.

Front

PVDM 1

Green

On indicates presence of a PVDM in PVDM slot 1.

Front

Содержание 2801 - Integrated Services Router













































































































































































































Результаты поиска

Содержание 2801 - Integrated Services Router

Отзывы:

Похожие инструкции для 2801 - Integrated Services Router

Бренды по названию

Популярные бренды

Cisco 2801 - Integrated Services Router, Руководство пользователя

Результаты поиска

Содержание 2801 - Integrated Services Router

Отзывы:

Похожие инструкции для 2801 - Integrated Services Router

Бренды по названию

Популярные бренды