Cisco 1800 Series Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 82

Cisco 1800 Series Скачать руководство пользователя страница 44

4-2

Cisco 1800 Series Integrated Services Routers (Fixed) Hardware Installation Guide

OL-6425-03

Chapter 4 Power, Cable, and Antenna Connection Procedures

Connecting WAN and LAN Cables

Note

The installation must comply with all required electrical codes applicable at the installation site.

Connecting Routers to AC Power

Connect your router to a 15A, 120-VAC (10A, 240-VAC) circuit with overcurrent protection.

Note

The input voltage tolerance limits for AC power are 90 and 264 VAC.

Warning

This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that
the protective device is rated not greater than:

15A, 120VAC (10A, 240VAC).

Statement 1005

Warning

This equipment has been designed for connection to TN and IT power systems.

Statement 1007

Warning

This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the
absence of a suitably installed ground conductor. Contact the appropriate electrical inspection
authority or an electrician if you are uncertain that suitable grounding is available.

Statement 1024

Warning

This equipment must be installed and maintained by service personnel as defined by AS/NZS 3260.
Incorrectly connecting this equipment to a general-purpose outlet could be hazardous. The
telecommunications lines must be disconnected 1) before unplugging the main power connector or 2)
while the housing is open, or both.

Statement 1043

Warning

When installing or replacing the unit, the ground connection must always be made first and
disconnected last.

Statement 1046

Connecting WAN and LAN Cables

This section describes how to connect the WAN, LAN, and voice interface cables. It covers the
following topics:

•

Preparing to Connect to a Network, page 4-3

•

Ports and Cabling, page 4-4

•

Connection Procedures and Precautions, page 4-5

Note

Ethernet cables and transceivers can be ordered from Cisco Systems. For ordering information, contact
customer service. For cable pinouts, refer to the

Cisco Modular Access Router Cable Specifications

document.

«
...
42
43
44
45
46
...
»

Содержание 1800 Series



















































































Отзывы:

Нет отзывов