manualshive.com logo in svg

Cisco 1800 Series, Руководство по установке оборудования, Страница: 21 / 82

Поделиться
Скачать
Cisco 1800 Series Скачать руководство пользователя страница 21

 

1-5

Cisco 1800 Series Integrated Services Routers (Fixed) Hardware Installation Guide

OL-6425-03

Chapter 1      Overview

  Hardware Features

For LED troubleshooting information, including possible trouble causes and corrective actions, see 

Table 6-1

 in the 

“Troubleshooting”

 chapter.

Integrated 802.11a/b/g Radio Module (Wireless Models Only)

The Cisco 1800 series fixed-configuration routers with the wireless option have an integrated IEEE 
802.11a/b/g radio module that operates as a wireless access point in infrastructure mode. The wireless 
routers have two 

reverse-polarity threaded Neill-Concelman (RP-TNC) connectors on the back panel. The 

dipole swivel antennas that were shipped with the router connect to the RP-TNC connectors to operate the 
802.11a/b/g radio module.

CD

2

Green

This LED indicates whether a connection is established (carrier detect). On the Cisco 1801, 
Cisco 1802, and Cisco 1803 routers, this LED indicates whether a DSL connection is 
established. On the Cisco 1811 router, this LED indicates whether a modem connection is 
established.

On indicates a connection is established.

Off indicates no connection established.

LPBK

3

Green

On indicates the DSL interface is in loopback mode.

Off indicates DSL interface normal operation.

PPP

Green

On if at least one PPP connection is established.

VPN

Green

On if at least one VPN tunnel is established.

LINK

4

Green

On indicates that an ISDN S/T connection has been established.

Off indicates that no ISDN S/T connection has been established.

B1

4

Green

Blinking green indicates activity on the first B channel.

Off indicates no activity on the first B channel.

B2

4

Green

Blinking green indicates activity on the second B channel.

Off indicates no activity on the second B channel.

SPD

5

Green

On indicates a connection at high speed (V.90/V.92).

Off indicates a connection at low speed (V.32/V.32b/V.34). 

BUSY

5

Green

Blinking green indicates activity over the modem line.

Off indicates no activity.

CF

Green

On when CompactFlash memory is busy. Do not remove CompactFlash memory when this 
light is on.

1.

Inline power is a field-upgradable option only. It is not installed by default.

2.

This LED does not exist on the Cisco 1812.

3.

This LED exists on the Cisco 1801, Cisco 1802, and Cisco 1803 only.

4.

This LED does not exist on the Cisco 1811.

5.

This LED exists on the Cisco 1811 only.

Table 1-3

Summary of LED Indicators on the Cisco 1800 Series Fixed-Configuration Routers (continued)

LED

Color

Description

Содержание 1800 Series



















































































Отзывы:

Нет отзывов