background image

CIS

-

80MKV ROUTER

 

PRODUCT MANUAL

 

8. PoE Information and Settings

 

PoE

-

Out Modes:

 

Auto

-

on mode

 

If auto

-

on is selected on a PoE

-

Out interface, then the port operates in this strict order:

 

• 

The router checks for resistance on the connected port. If the detected resistance range is between (3k

Ω 

to 26.5k

Ω), 

the

 

power is turned on.

 

• 

When power is applied, the router continuously checks if the overload limit is reached, or if a short circuit is detected.

 

• 

If the cable is unplugged, the port returns to the detection state, and will remain off until suitable power draw is detected.

 

 

Forced

-

on mode

 

If forced

-

on is selected, then the port operates in this strict order:

 

• 

There is no resistance check on the port. The router applies power on pins 4,5 (+) and 7,8 (

-

), even if no cable is attached.

 

• 

When power is applied, the router continuously checks if an overload or a short circuit is detected.

 

• 

After the cable is unplugged, the power still remains enabled on the port.

 

 

Off mode

 

If off mode is used, PoE

-

Out on the port will be turned off, no detection will take place, and the interface will behave as a sim-

ple Ethernet port.

 

 

PoE

-

Out limitations

 

It is important to check the PoE

-

Out specifications for hardware limitations because it can differ between models.

 

PoE

-

Out ports are limited with maximum amp values which are supported for a particular voltage. Usually max current will 

differ for low voltage devices (up to 30 V), and for high voltage devices (31 to 57 V).

 

PoE supplying devices also have a total current limitation which can't be exceeded, even if individual port limit allows it.

 

All CIS equipment uses the same PoE

-

Out pin polarity

 

Mode B

 

4,5 (+) and 7,8 (

-

), however other vendors can use opposite o r 

Mode A pinout on PD, this requires using a special

 

crossover cable

 

 

Enable/Disable PoE on a Specific Port

 

On the CIS

-

MK80V, only port 10 is capable of powering devices through PoE. Select port 10 from the 

Interfaces

 tab. Change the 

PoE Out option accordingly.

 

Содержание CIS-80MKV





























Отзывы: