Cirrus Logic CDB48500-USB Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 52

Cirrus Logic CDB48500-USB Скачать руководство пользователя страница 18

CDB48500 System Block Descriptions

CDB485x00-USB Evaluation Kit Guide

DS784DB1

©

Copyright 2008 Cirrus Logic , Inc.

3-2

3.1 CDB48500 System Block Descriptions

3.1.1 Audio Inputs

3.1.1.1 Analog Line-level Inputs

•

Connector Type: RCA Female

•

Absolute Maximum Signal Level: +6.5V

•

Absolute Minimum Signal Level: GND - 0.7V

•

Full Scale Amplitude: 2V

RMS

•

Reference Designators: J4, J6-J10, J12, J26-J30, or AIN1A - AIN6B

3.1.1.2 Digital Optical Input

Note: Digital Optical Input is PCM only as there is no multi-channel decoder present on CDB48500-

USB.

•

Connector Type: Fiber Optic RX for Digital Audio, JIS F05 (JIS C5974-1993 F05)

•

Reference Designator: J2, or SPDIF_RXP

3.1.1.3 Digital Coaxial Input

Note: Digital Coaxial Input is PCM only as there is no multi-channel decoder present on CDB48500-

USB.

•

Connector Type: RCA Female

•

Maximum Signal Level: +3.3V

•

Minimum Signal Level: GND - 0.7V

•

Reference Designator: J31, or SPDIF_RXN

3.1.1.4 Microphone Input

•

Absolute Maximum Signal Level: +5V

•

Absolute Minimum Signal Level: GND - 0.7V

•

Full Scale Amplitude: 7mVp-p

•

Reference Designator: J5

The microphone preamplifier shares the AIN1_5 ADC with the AIN3_A RCA jack. Only one analog source
can be sampled at any given time. When the microphone input is selected, the AIN3_A audio jack is
ignored. The default configuration enables the AIN3_A audio jack.

3.1.2 Audio Outputs

3.1.2.1 Analog Line-level Outputs

•

Connector Type: RCA Female

•

Full Scale Amplitude: 1.21V

RMS

•

Reference Designators: J13-J16, J33-J40, or AOUT_1A - AOUT_6B

«
...
16
17
18
19
20
...
»

Содержание CDB48500-USB





















































Отзывы:

Нет отзывов