CS42528
18
DS586PP5
AD0/CS
10
Address Bit 0 (I
2
C)/Control Port Chip Select (SPI)
(Input
)
-
AD0 is a chip address pin in I
2
C mode; CS
is the chip select signal in SPI mode.
INT
11
Interrupt
(Output
) - The CS42528 will generate an interrupt condition as per the Interrupt Mask register.
See “Interrupts” on page 40 for more details.
RST
12
Reset
(
Input
) - The device enters a low power mode and all internal registers are reset to their default
settings when low.
AINR-
AINR+
13
14
Differential Right Channel Analog Input
(
Input
) - Signals are presented differentially to the delta-sigma
modulators via the AINR+/- pins.
AINL+
AINL-
15
16
Differential Left Channel Analog Input
(
Input
) - Signals are presented differentially to the delta-sigma
modulators via the AINL+/- pins.
VQ
17
Quiescent Voltage
(
Output
)
-
Filter connection for internal quiescent reference voltage.
FILT+
18
Positive Voltage Reference
(
Output
) - Positive reference voltage for the internal sampling circuits.
REFGND
19
Reference Ground
(
Input
) - Ground reference for the internal sampling circuits.
,-
,-
,-
,-
,-
,-
,-
,-
36,37
35,34
32,33
31,30
28,29
27,26
22,23
21,20
Differential Analog Output
(
Output
) - The full-scale differential analog output level is specified in the
Analog Characteristics specification table.
VA
VARX
24
41
Analog Power
(
Input
) - Positive power supply for the analog section.
AGND
25
40
Analog Ground
(
Input
) - Ground reference. Should be connected to analog ground.
MUTEC
38
Mute Control
(
Output
) - The Mute Control pin outputs high impedance following an initial power-on con-
dition or whenever the PDN bit is set to a ‘1’, forcing the codec into power-down mode. The signal will
remain in a high impedance state as long as the part is in power-down mode. The Mute Control pin goes
to the selected “active” state during reset, muting, or if the master clock to left/right clock frequency ratio
is incorrect. This pin is intended to be used as a control for external mute circuits to prevent the clicks
and pops that can occur in any single supply system. The use of external mute circuits are not manda-
tory but may be desired for designs requiring the absolute minimum in extraneous clicks and pops.
LPFLT
39
PLL Loop Filter
(
Output
) - An RC network should be connected between this pin and ground.
RXP7/GPO7
RXP6/GPO6
RXP5/GPO5
RXP4/GPO4
RXP3/GPO3
RXP2/GPO2
RXP1/GPO1
42
43
44
45
46
47
48
S/PDIF Receiver Input/ General Purpose Output
(
Input/Output
) - Receiver inputs for S/PDIF encoded
data. The CS42528 has an internal 8:2 multiplexer to select the active receiver port, according to the
Receiver Mode Control 2 register. These pins can also be configured as general purpose output pins,
ADC Overflow indicators or Mute Control outputs according to the RXP/General Purpose Pin Control
registers.
RXP0
49
S/PDIF Receiver Input
(
Input
) - Dedicated receiver input for S/PDIF encoded data.
TXP
50
S/PDIF Transmitter Output
(
Output
) - S/PDIF encoded data output, mapped directly from one of the
receiver inputs as indicated by the Receiver Mode Control 2 register.
VLS
53
Serial Port Interface Power
(
Input
) - Determines the required signal level for the serial port interfaces.
SAI_SDOUT
54
Serial Audio Interface Serial Data Output
(
Output
) - Output for two’s complement serial audio PCM
data from the S/PDIF incoming stream. This pin can also be configured to transmit the output of the inter-
nal and external ADCs.
RMCK
55
Recovered Master Clock
(
Output
) - Recovered master clock output from the External Clock Reference
(OMCK, pin 59) or the PLL which is locked to the incoming S/PDIF stream or CX_LRCK.
