Cirronet HopNet HN-210X Скачать руководство пользователя страница 53

Страница: 53 / 64

HopNet RS-232 Serial ModBus Radio

Adapter Commands

The following commands are available via WinCom24.

Command

Description

qp[?|0|1|2]

Protocol Mode

0 = Transparent mode. Non-Modbus mode

1 = Modbus mode. Supports encapsulation of data to ensure

continuous send-out on receiver side. Also supports the learning

of Modbus addresses.

2 = Encapsulation mode. Encapsulates the incoming data and uses

QD to protect the data from gaps, but does not perform the

Modbus

addressing.

qs[?|0-8]

Serial Data Options

0 = No parity, 8 bit data, 1 stop bit (default)

1 = Odd parity, 8 bit data, 1 stop bit

2 = Even parity, 8 bit data, 1 stop bit

3 = No parity, 7 bit data, 2 stop bits

4 = Even parity, 7 bit data, 2 stop bits

5 = Odd parity, 7 bit data, 2 stop bits

6 = No parity, 7 data bits, 1 stop bit

7 = Even Parity, 7 data bits, 1 stop bit

8 = Odd Parity, 7 data bits, 1 stop bit

qw[?|0|1|2]

Adapter Wiring Mode

0 = Normal, “full wire” mode

1 = Three-wire mode (RX, TX, GND)

2 = Three-wire mode + DTR

Modbus Delay This will be ignored on QP0 (Transparent) mode

Multiply QD by 3ms. This is the amount of time that the adapter will

hold data from the WIT while anticipating an end of the Modbus or

DNP3 packet. If this time expires before the end of the packet

arrives, then the data is released and hopefully the rest of the packet

will arrive before the stored data is exausted. If not, an error may

occur. If the end of the packet arrives before the time expires, the

data is released early.

2000- 2004 Cirronet

™

Inc

M-2410-0022 Rev B

Содержание HopNet HN-210X

































































Результаты поиска

Содержание HopNet HN-210X

Отзывы:

Бренды по названию

Популярные бренды

Cirronet HopNet HN-210X, Руководство пользователя

Результаты поиска

Содержание HopNet HN-210X

Отзывы:

Бренды по названию

Популярные бренды