manualshive.com logo in svg

Cirronet HopNet HN-210X, Руководство пользователя

Поделиться
Скачать
Cirronet HopNet HN-210X Скачать руководство пользователя страница 22

HopNet RS-232 Serial ModBus Radio 

 

 

When the radio is linked to another radio, a communications test can be run by 
clicking on the Send Data button (shown below) on both radios. The remote radio’s 
Transmit Data window (above left) will display the message, “This is a test message 
from the Base radio”, which will repeat until the Stop button is pressed (on the base 
radio’s HN Wizard main screen). The base radio’s Transmit Data window (above 
right) will display the message, “This is a test message from the Remote radio” which 
will repeat until the Stop button is pressed (on the remote radio’s HN Wizard main 
screen).  

Send Data  

The Send Data button (shown below) initiates the transmission of data. 

 

Default  

The Default button (shown above) returns all parameters to Factory settings. 

©

 2000- 2004 Cirronet

™

 Inc 

16 

M-2410-0022 Rev B 

Содержание HopNet HN-210X

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды