manualshive.com logo in svg

Cirronet HopNet HN-210X, Руководство пользователя

Поделиться
Скачать
Cirronet HopNet HN-210X Скачать руководство пользователя страница 10

HopNet RS-232 Serial ModBus Radio 

Getting Started 

A pair of HopNet radios are set up by performing the following steps: 

•

 

Install the HopNet Wizard configuration program on a PC 

•

 

Connect the HopNet radio to the PC 

•

 

Set one HopNet radio as a base radio 

•

 

Run a communications test 

These steps are described in detail below. Other steps you may want to perform 
include: 

•

 

Change the baud rate 

•

 

Change the radio network number 

•

 

Change how fast the radios change frequencies 

Refer to the 

Configuring the Network

 section of this manual for details on these steps. 

Install the HopNet Configuration Wizard on a PC. 

The HopNet Configuration Wizard is located on the software and documentation CD 
included in the HopNet radio package. Install the program by inserting the CD in the 
PC and following the installation wizard. If autorun has been turned off, double-click 
on setup.exe on the CD to start the wizard. 

Connect the HopNet radio to the PC. 

 

Plug one end of the serial cable provided to a serial port on the PC. 

©

 2000- 2004 Cirronet

™

 Inc 

4 

M-2410-0022 Rev B 

Содержание HopNet HN-210X

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды