manualshive.com logo in svg

Cirronet HopNet HN-210X, Руководство пользователя

Поделиться
Скачать
Cirronet HopNet HN-210X Скачать руководство пользователя страница 5

 

Table of Contents 

Introduction .................................................................................................................. 1

 

HopNet Benefits ........................................................................................................... 1

 

Operating Frequency ............................................................................................... 1

 

HopNet Frequency Hopping Spread Spectrum Advantages .................................... 1

 

HopNet Data Integrity............................................................................................... 2

 

Flexible Power Management.................................................................................... 2

 

Advanced Features ...................................................................................................... 3

 

The HopNet Family of Products ................................................................................... 3

 

Accessories.............................................................................................................. 3

 

Getting Started ................................................................................................................ 4

 

Install the HopNet Configuration Wizard on a PC. ....................................................... 4

 

Connect the HopNet radio to the PC. ........................................................................... 4

 

Set one HopNet radio to act as the base...................................................................... 5

 

Run a communications test. ......................................................................................... 7

 

The Serial Adapter Box ................................................................................................ 8

 

3 Wire Operation ...................................................................................................... 8

 

Remote Pin-Out, RS-232 ......................................................................................... 9

 

Guidelines for Installation ........................................................................................... 10

 

Aiming the Antenna and Placing the Remote............................................................. 10

 

Interconnect Cable ..................................................................................................... 10

 

Configuring the Network................................................................................................ 11

 

HopNet Configuration Wizard (5.0 or later) ................................................................ 11

 

About the INIT.INI File................................................................................................ 12

 

Parameters Tab ..................................................................................................... 13

 

Network Tab........................................................................................................... 17

 

Protocol Tab........................................................................................................... 20

 

RF Tools ................................................................................................................ 22

 

WinCom Window.................................................................................................... 26

 

Function Keys ........................................................................................................ 29

 

Recover.................................................................................................................. 29

 

Restart ................................................................................................................... 30

 

Saving Configurations ................................................................................................ 30

 

About Protocols .......................................................................................................... 30

 

Modbus Operation...................................................................................................... 32

 

Automatic Addressing ............................................................................................ 33

 

DNP3/DF1 Operation ................................................................................................. 33

 

European Union Operation......................................................................................... 34

 

Configuration Commands.............................................................................................. 35

 

Serial Commands....................................................................................................... 36

 

Network Commands................................................................................................... 38

 

Protocol Commands................................................................................................... 41

 

Status Commands...................................................................................................... 44

 

Memory Commands ................................................................................................... 46

 

Adapter Commands ................................................................................................... 47

 

Modem Command Summary ..................................................................................... 48

 

Содержание HopNet HN-210X

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды