Circutor OPTIM HYB Series Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 36

background image

3.- INSTALLATION

3.1.- PRELIMINARY RECOMMENDATIONS

In order to use the unit safely, it is critical that individuals who handle it follow the

safety measures set out in the standards of the country where it is being used,

use the personal protective equipment necessary, and pay attention to the vari-

ous warnings indicated in this instruction manual.

Installation or maintenance personnel should read and understand this manual

before operating the unit.

A copy of this manual should always be available to maintenance personnel for

reference purposes

Connecting the unit to the public mains must be carried out in compliance with

the EN-IEC60204-1 standard, regarding the safety of LV electrical installations.

It is recommended that several personnel are present when handling the unit for

installation or maintenance.

If damage or faults are detected during unit operation, or in circumstances that

compromise safety, immediately stop work in that area and disconnect the unit in

order to check it without voltage.

The manufacturer of the unit is not responsible for any damages resulting from failure by the

user or installer to heed the warnings and/or recommendations set out in this manual, nor for

damages resulting from the use of products or accessories that did not come with the unit or

that were made by other manufacturers.

If an anomaly or malfunction is detected in the unit, do not use it to perform any operation.

Modifying, upgrading or rebuilding the unit without written authorisation from the

manufacturer is prohibited.

The installation, operation and maintenance of low voltage (LV) units must only

be carried out by authorised installers. LV regulations (Art. 22) specifically define

the requirements that authorised installers must meet.
Do not access the active elements of a capacitor bank with static operation that

has been powered and might have voltages present. Wait at least

5 minutes

af-

ter the power supply has been disconnected.
Do not touch the terminals or active parts of the unit until you have verified that

voltage is not present. If you have to handle or touch the terminals or other control

panel components, use adequately insulated personal protection equipment and

tools.
After any maintenance and before re-connecting the power supply to the unit,

check that its enclosure is properly closed and that no items or tools were left

inside that could cause a short-circuit.

15

Instruction Manual

OPTIM HYB Series

«
...
13
14
15
16
17
...
»

Содержание OPTIM HYB Series





































Отзывы:

Нет отзывов

Похожие инструкции для OPTIM HYB Series

Бренд: National Instruments Страницы: 10

Бренд: National Instruments Страницы: 39

Бренд: Grundfos Страницы: 43

SmartShop II SUV

Бренд: laguna Страницы: 26

ANT130LZ Series

Бренд: Aerotech Страницы: 52

Бренд: Danfoss Страницы: 33

FS80-H445.106 S29A2W2/2V

Бренд: Jäger Страницы: 40

Бренд: Huayu Страницы: 12

GRIT GXR Series

Бренд: Fein Страницы: 16

Бренд: National Instruments Страницы: 55

Бренд: iceqube Страницы: 29

Бренд: Parker Страницы: 52

Rotavapor R-187EL

Бренд: Buchi Страницы: 42

Бренд: OBO Bettermann Страницы: 3

KTR-STOP TB Thuster

Бренд: KTR-Group Страницы: 17

Бренд: Enerpac Страницы: 68

Бренд: SeaLevel Страницы: 53

Бренд: Stark Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды