manualshive.com logo in svg

CIRCUIT DESIGN MU-D1-R, Руководство по эксплуатации

Поделиться
Скачать
CIRCUIT DESIGN MU-D1-R Скачать руководство пользователя страница 52

 

OG_MU-D1-R_v010e                                                                                   

                   

      Circuit  Design,  Inc.

 

52

 

 

 
 
USA-Federal Communications Commission (FCC)

 

 
The MU-D1-R complies with Part 15 of the FCC Rules. 
Operation is subject to the following two conditions: 
(1) This device may not cause harmful interference, and 
(2) This device must accept any interference received, including interference that may cause undesired operation. 

 
 
Caution

 

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s 
authority to operate the equipment. 
 

 
Labeling 

Circuit Design RF module MU-D1-R labeled as below. 

FCC ID: V9X-MUD1R 

The proposed with FCC ID label format is to be placed on the module. If FCC ID is not visible when the module is 
installed into the system, “Contains FCC ID: V9X-MUD1R ” shall be placed on the outside of final host system.   
 

 
Caution: Exposure to Radio Frequency Radiation. 

To  comply  with  FCC  RF  exposure  compliance  requirements,  a  separation  distance  of  at  least  20  cm  must  be 
maintained between the antenna of this device and all persons. This device must not be co-located or operating in 
conjunction with any other antenna or transmitter.

   

 
 

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 
of  the  FCC  Rules.  These  limits  are  designed  to  provide  reasonable  protection  against  harmful  interference  in  a 
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed 
and used in accordance with the instructions, may cause harmful interference to radio communications. However, 
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful 
interference to radio or television reception, which can be determined by turning the equipment off and on, the user 
is encouraged to try to correct the interference by one or more of the following measures: 
-  Reorient or relocate the receiving antenna. 
-  Increase the separation between the equipment and receiver. 
-  Connect the equipment into and outlet on a circuit different from that to which the receiver is connected. 
-  Consult the dealer or an experienced radio/TX technician for help. 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 

Chapter 9 Regulatory Compliance

 

9.1 Regulatory Compliance of the MU-D1-R

 

 

Содержание MU-D1-R























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды