2. Replace the lid ensuring the o-ring is correctly located and start the pump.
After you have done this allow a few minutes (maximum) running for the pump to start
delivering water.
High suction lift or long suction lines will require additional time to prime and can severely
affect the performance of the pump. If the pump does not
above. Mechanical seals if running dry can be damaged rapidly and may need to be replaced.
ENSURE that there is always adequate water in the filter tank before you start up.If you are
unable to prime the pump please see t
ENSURE that all suction and discharge valves are open before you start the pump, otherwise
will result in damage to the pump.
9.Maintenance
The strainer basket in the filter tank should be inspected and cleaned at regular interv
1. Remove lid and lift out basket.
2. Remove debris and hose off with clean water if necessary.
3. Inspect the lid gasket, lubricate with silicon based grease
only if needed. If it is damaged, pls replace.
4. Replace the strainer.
5. Re-prime the filter tank.
6. Correctly locate the o-ring.
7. Replace the lid hand tighten only.
8. Switch on pump.
In Climates where the pump may be exposed to frost or freezing,
the pump is protected from damage.
winter period it should be drained completely and store pump in a dry location. Do not replace
the drain plug. Store it in a safe place when not use. An example would be store plug in the
filter tank basket.
When you are activated the pump ensures all seals and o
re-grease if necessary, replaced if unsure of condition.
Check that the motor shaft moves freely before re
1. When connecting electric cables to the motor of the pump,
them inside the connection box, verify that no bits of cable are left inside the box on closing it.
See that the ground wire is correctly connected.
diagram supplied with the pump.
2. Be especially careful that no water enters the motor or electrical parts under voltage.
3. In the event that the planned use is not as specified, adaptations and supplementary
technical rules may be necessary.
ring is correctly located and start the pump.
After you have done this allow a few minutes (maximum) running for the pump to start
High suction lift or long suction lines will require additional time to prime and can severely
affect the performance of the pump. If the pump does not prime, please repeat step 1 and 2
above. Mechanical seals if running dry can be damaged rapidly and may need to be replaced.
ENSURE that there is always adequate water in the filter tank before you start up.If you are
unable to prime the pump please see the trouble-shooting guide.
ENSURE that all suction and discharge valves are open before you start the pump, otherwise
The strainer basket in the filter tank should be inspected and cleaned at regular interv
2. Remove debris and hose off with clean water if necessary.
3. Inspect the lid gasket, lubricate with silicon based grease
only if needed. If it is damaged, pls replace.
only.
In Climates where the pump may be exposed to frost or freezing, care must be taken to ensure
the pump is protected from damage. It is recommended that if the pump is not used during
winter period it should be drained completely and store pump in a dry location. Do not replace
the drain plug. Store it in a safe place when not use. An example would be store plug in the
ted the pump ensures all seals and o-rings are in operational condition,
grease if necessary, replaced if unsure of condition.
Check that the motor shaft moves freely before re-activation.
1. When connecting electric cables to the motor of the pump, be careful to correctly arrange
them inside the connection box, verify that no bits of cable are left inside the box on closing it.
ground wire is correctly connected. When connecting the motor, follow the wiring
that no water enters the motor or electrical parts under voltage.
3. In the event that the planned use is not as specified, adaptations and supplementary
After you have done this allow a few minutes (maximum) running for the pump to start
High suction lift or long suction lines will require additional time to prime and can severely
prime, please repeat step 1 and 2
above. Mechanical seals if running dry can be damaged rapidly and may need to be replaced.
ENSURE that there is always adequate water in the filter tank before you start up.If you are
ENSURE that all suction and discharge valves are open before you start the pump, otherwise
The strainer basket in the filter tank should be inspected and cleaned at regular intervals.
are must be taken to ensure
the pump is not used during
winter period it should be drained completely and store pump in a dry location. Do not replace
the drain plug. Store it in a safe place when not use. An example would be store plug in the
rings are in operational condition,
be careful to correctly arrange
them inside the connection box, verify that no bits of cable are left inside the box on closing it.
When connecting the motor, follow the wiring
that no water enters the motor or electrical parts under voltage.
3. In the event that the planned use is not as specified, adaptations and supplementary
14
