Cincinnati Fan LM Скачать руководство пользователя

Страница: 9 / 15

OMM-23-1009-page 9

Fig. 4 Vibration Severity Chart

BEFORE STARTING ANY INSPECTION OR MAINTENANCE, BE SURE BLOWER IS TURNED OFF, POWER IS LOCKED

OUT AND THE BLOWER WHEEL HAS BEEN CAREFULLY SECURED TO PREVENT WIND MILLING. IF THE

OPERATING CONDITIONS OF THE BLOWER ARE TO BE CHANGED (SPEED, PRESSURE, TEMPERATURE, ETC.)

CONSULT CINCINNATI FAN, OR OUR SALES OFFICE FOR YOUR TERRITORY, TO DETERMINE IF THE UNIT WILL

OPERATE SAFELY AT THE NEW CONDITIONS.

WARNING

V. ROUTINE INSPECTION & MAINTENANCE

Periodic inspection of all the blower parts is the key to good maintenance and trouble-free operation. The frequency of
inspections must be determined by the user and is dependent upon the severity of the application.

BUT,

it should

NEVER

exceed a 12 month period. The user should prepare an inspection and maintenance schedule and make sure

it is adhered to.

Содержание LM
















Результаты поиска

Содержание LM

Отзывы:

Похожие инструкции для LM

Бренды по названию

Популярные бренды

Cincinnati Fan LM, Инструкция по установке, безопасности, эксплуатации и техническому обслуживанию, а также перечень запасных частей.

Результаты поиска

Содержание LM

Отзывы:

Похожие инструкции для LM

Бренды по названию

Популярные бренды