background image

IX. LIMITED WARRANTY:

Cincinnati Fan & Ventilator Company (Seller) warrants products of its own manufacture, against defects of material and workmanship
under normal use and service for a period of eighteen (18) months from date of shipment or twelve (12) months from date of installa-
tion, whichever occurs first. This warranty does not apply to any of Seller’s products or any part thereof which has been subject to
extraordinary wear and tear, improper installation, accident, abuse, misuse, overloading, negligence or alteration. This warranty does
not cover systems or materials not of Seller’s manufacture. On products furnished by Seller, but manufactured by others, such as
motors, Seller extends the same warranty as Seller received from the manufacturer thereof. Expenses incurred by Purchaser’s in
repairing or replacing any defective product will not be allowed except where authorized in writing and signed by an officer of the
Seller.

The obligation of the Seller under this warranty shall be limited to repairing or replacing F.O.B. the Seller’s plant, or allowing credit at
Seller’s option. 

THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EITHER EXPRESSED OR IMPLIED

INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AND OF ALL OTHER
OBLIGATIONS AND LIABILITIES OF THE SELLER. THE PURCHASER ACKNOWLEDGES THAT NO OTHER REPRESENTA-
TIONS WERE MADE TO PURCHASER OR RELIED UPON BY PURCHASER WITH RESPECT TO THE QUALITY OR FUNCTION
OF THE PRODUCTS HEREIN SOLD.

Removal of the Sellers nameplate or any generic fan nameplate containing the fan serial number voids all warranties, either written or
implied. Failure to complete and document all the pre-startup and post startup checks and perform the suggested routine mainte-
nance checks voids all warranties, either written or implied.

LIMITATION OF LIABILITY:

Notice of any claim, including a claim for defect in material or workmanship, must be given to Seller in writing within 30 days after
receipt of the equipment or other products. Seller reserves the right to inspect any alleged defect at Purchaser’s facility before any
claim can be allowed and before adjustment, credit, allowance replacement or return will be authorized. See 

RETURNS

below.

Seller’s liability with respect to such defects will be limited to the replacement, free of charge, of parts returned at Purchaser’s
expense F.O.B. Seller’s plant and found to be defective by the Seller.

IN NO EVENT WILL SELLER BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, WHETHER
IN CONTACT, TORT, NEGLIGENCE, STRICT LIABILITY OR OTHERWISE, INCLUDING WITHOUT LIMITATION DAMAGES FOR
INJURY TO PERSONS OR PROPERTY, LOST PROFITS OR REVENUE, LOST SALES OR LOSS OF USE OF ANY PRODUCT
SOLD HEREUNDER. PURCHASER’S SOLE AND EXCLUSIVE REMEDY AGAINST SELLER WILL BE THE REPLACEMENT OF
DEFECTIVE PARTS AS PROVIDED HEREIN OR REFUND OF THE PURCHASE PRICE FOR DEFECTIVE PRODUCTS, AT SELL-
ER’S SOLE OPTION. SELLER’S LIABILITY ON ANY CLAIM, WHETHER IN CONTRACT, TORT, NEGLIGENCE, STRICT LIABILI-
TY OR OTHERWISE, FOR ANY LOSS OR DAMAGE ARISING OUT OF OR IN CONNECTION WITH PURCHASER’S ORDER OR
THE PRODUCTS OR EQUIPMENT PURCHASED HEREUNDER, SHALL IN NO CASE EXCEED THE PURCHASE PRICE OF THE
EQUIPMENT GIVING RISE TO THE CLAIM.

RESPONSIBILITY:

It is the understanding of the Seller that Purchaser and/or User will use this equipment in conjunction with additional equipment or
accessories to comply with all Federal, State and local regulations. The Seller assumes no responsibility for the Purchaser’s or Users
compliance with any Federal, State and local regulations.

RETURNS:

Cincinnati Fan & Ventilator Company assumes no responsibility for any material returned to our plant without our permission. An 

RMA

(Return Material Authorization) number must be obtained and clearly shown on the outside of the carton or crate and on a packing
slip. Any items returned must be shipped freight prepaid. Failure to comply will result in refusal of the shipment at our receiving
department.

OMM-23-1009-page 14

DISCLAIMER

This manual, and all its content herein, is based on all applicable known material at the time this manual was created. 

Any parts of

this manual are subject to change at any time and without notice. 

If any statements, diagrams and/or instructions contained herein, 

for components not manufactured by the Seller,

conflict with

instructions in the manufacturer’s manual (i.e.: motors, dampers, etc.), the instructions in the manufacturer’s manual, for that compo-
nent take precedent.
Should you want the latest version of this manual, please contact us or our sales office for your area. Or, you can print a current ver-
sion by going to our website at: 

www.cincinnatifan.com

7697 Snider Road, Mason, OH 45040-9135
Phone: (513) 573-0600

Fax: (513) 573-0640

E-Mail: [email protected]

Содержание LM
















Отзывы: