CIMLINE MA4, Руководство владельца/оператора

Страница: 9 / 60

9
NOTE
: This general outline will familiarize you with this machine dependent on model,
location and style and may vary with options installed. Read through the entire manual before
putting this machine into operation.
1) Main Control Panel: The main control panel is used to control the primary functions of the melter,
including simple automated user controls for Off / Run / Clean Out / Cool Down as well as manual control
of the sealant material pump direction and tank agitator. You can also monitor or adjust the temperature of
the sealant material and heat transfer oil on the control sub panel. See page 10 for more information on
the main control panel.
2) MA4 Applicator Electronic Control Display: This computerized panel will allow you to set your
application rate and calibrate the output rate of the sealant material through the application bar. See page
11 for more information on the electronic control unit.
3) Loading Door: Place the sealant material block or biscuit on the open door to load the melting
tank. See page 14 for more information on safely loading sealant material into the melter.
4) Heat Transfer Oil Level Dipstick: Allows you to monitor the amount of heat transfer oil in the
melter oil tank. See page 25 for more information on using the heat transfer oil dipstick.
5) Heat Transfer Oil Temperature Gauge: Displays the heat transfer oil temperature.
6) Ignition Switch: Engine key “ Start” / “ On” / “ Off” and also displays engine running hours, glow
plug status, alternator charge, engine oil pressure and engine coolant warnings.
7) Main Tank Valve: “ Open” / “ Shut” allows sealant material to enter pump from sealant material
tank.
8) Control Handles (Qty. 2): Controls flow from “ Circulation” re-circulation back to sealant material tank
and “Spray Bar Circulate” circulation through application bar and back to sealant material tank.
9) Bulk Loading Plug: This 3 inch Cam and Groove fitting allows for liquefied bulk sealant material to
be pumped directly into the MA4 sealant material tank from an external source.
10) Secondary Tank Valve: Allows sealant material to enter the Draw Off / Sample system out to the
Draw Off / Sample Valve.
11) Draw Off / Sample Valve: Allows sealant material to gravity pour into a pour pot for manual
application on areas unreachable by the application bar, or can be used for drawing off sealant material
samples for testing purposes.
12) Pour Pot Storage: Two pour pots can be stored in this external box. Items in this box must be tied
down properly while in transport.
13) Control Lights: These lights are visible to the driver and indicate when the system is ready to
begin application and that the vehicle is driving an appropriate speed for the application rate. See page 16
for more information on the control lights.
14) Ground Speed Encoding Wheel: This sensor folds up / down for storage and reports trailer speed
to the computerized control system. The control system communicates with the pump to apply the
appropriate amount of sealant material based on the speed reported by this wheel. See page 16 for more
information on the ground speed encoding wheel.
15) Application Bar: The application bar folds up / down for storage. When the control valves are
opened to “Spray Bar Circulate” hot sealant material circulates through the application bar until the system
is activated and senses movement, dispensing sealant material as directed by the control system.
16) Tip Control Keypad: You can manually control and engage the application tips from this keypad
(or with the key fob remote). See page 20 for more information on the tip control keypad
17) Key Fob Remote Transmitter: The MA4 comes with 1 wireless remote to activate the application of
sealant material from the application bar. The key fob remote transmitter also can control which of the 5
spray tips are actively applying sealant material. Note: Only one remote can be actively powered on at a
time. See page 16 for more information on the key fob remote transmitter. See page 20 for information on
pairing the key fob remote transmitter.
MA4 Feature Overview