background image

11

4. Installation cautions

Follow the instruction for proper drainage of product.   

Manufacturer is not responsible for any damage or reduced

performance from wrong installation. 

Instruction of installation

(1) Use bigger than a size of 3/8"drain tube (O.D.: outer

diameter) without connector (ex. Fitting) from A to B. 

(Refer to the Pic 1.)

Avoid using 1/4"drain tube (O.D.) with a reducer (3/8" 

1/4"). You should follow this instruction to prevent the

water leakage or overflow from incomplete drainage. 

(2) In case of U-Trap pipe type, change the shape of end of

drain tube same as the picture on the right. 

(Refer to the Pic 2. A, B, C)

It prevents the drain tube (3/8") from being clogged

with dirt. And it helps drainage well with proper air flow.

(3) Do not put the end of drain tube into the water. 

(Refer to the Pic 2)

(4) The highest point of installed drain tube must be less than 8"(20cm) away from the flat floor. (Refer to the Pic 1)

(5) Total length of drain tube must be less than 197"(5m). In case of longer than the stated length of drain tube  , 

drain pump is necessary to install.

(6) Black insulation tape is recommended to tie up 3/8" drain tube rather than cable tie. (Tight tying with cable tie can

interrupt the drainage.)

(7) After installation the product, pour the water (about 1

) into the water gutter to remove air inside. And check

out water draining properly from the water gutter. If the water is not drained well, reinstallation of drain tube

is needed. 

If  you  put  the  end  of  drain  tube  into  remaining

water  in  the  U-Trap  pipe

(

D

)

deeply  or  in  case  the

hole

(

C

)

of  drainpipe  is  sealed,  it  can  hinder  water

flow.  It  increases  the  hydrostatic  pressure  and  this

causes water overflowing up to the water gutter. 

<

Pic 1. Drawing of drain tube installation

>

5m

20cm

A

B

C

A

B

<

Pic 2. The shape of end of drain tube (3/8")

>

Dirt pile causes 

incomplete drainage.

Dirt

Drain line(3/8")

Brine line(1/4")

Water gutter

Ice storage

Dirt

Sewage

Sewage

Sewage

Split shape

Make more than 3air holes

Sewage

Drainpipe

Ground

Caution

Notice of Drain tube installation

T-461_영문매뉴얼_T_461_메뉴얼_5170S  12. 4. 10.  오후 4:32  페이지 12

Содержание Iguassu T-461

























Отзывы: