Chungho IGUASSU ICE Скачать руководство пользователя страница 38

Страница: 38 / 58

ouble

Shooting

Push the Ice button to dispense Ice.

There is Ice, but no Ice is dispensing - Check Ice shape.
- Remove Front-Upper cover and disassemble the dispense tunnel to check the shape of Ice.

Comp. is working properly, but there is no Ice.
ex> One tray of Ice is made approx. every 10 minutes at 77°F

If there is a 3min difference in the interval of time of Ice making, check the Environment
sensor.

12-3-C. ENVIRONMENT SENSOR DEFECT

Symptom

1. Cold water is working properly, but there is no Ice.
2. Connect Test Board: LED22 starts blinking.

Cause of Defect

If Environment sensor recognizes that the temperature is high, it may cause the Ice to make for longer
period of time, causing the Axle Coupling Motor to malfunction.

AS Procedure

1) Check ohm reading of sensor (Resistance should be approx. 45)
2) If sensor is defective, replace sensor.

How to Diagnose

Содержание IGUASSU ICE



























































Результаты поиска

Содержание IGUASSU ICE

Отзывы:

Похожие инструкции для IGUASSU ICE

Бренды по названию

Популярные бренды

Chungho IGUASSU ICE, Техническое руководство

Результаты поиска

Содержание IGUASSU ICE

Отзывы:

Похожие инструкции для IGUASSU ICE

Бренды по названию

Популярные бренды