![Chrysler Voyager 2001 Скачать руководство пользователя страница 59](http://html1.mh-extra.com/html/chrysler/voyager-2001/voyager-2001_operating-information-manual_2606246059.webp)
ELECTRONIC SPEED CONTROL
This device can be engaged to take over the
accelerator operation at speeds between 48 km/h
(30 mph) and 160 km/h (100 mph). The controls
are mounted on the steering wheel.
To Activate:
Push the “ON/OFF” button once and the CRUISE
indicator located below the instrument cluster
odometer will illuminate showing the electronic
speed control is on. To turn the system OFF, push
the “ON/OFF” button again and the system and
indicator will turn off.
WARNING!
Leaving the Electronic Speed Control system on
when not in use is dangerous. You could acci-
dently set the system or cause it to go faster
than you want. You could lose control and have
an accident. Always leave the system OFF
when you are not using it.
To Set At A Desired Speed:
When the vehicle has reached the desired speed,
press and release the “SET” button. Release the
accelerator and the vehicle will operate at the
selected speed.
To Deactivate:
A soft tap on the brake pedal, pushing the “CAN-
CEL” button or normal braking while slowing the
vehicle will deactivate the speed control without
erasing the memory. Pressing the clutch pedal will
also deactivate the system if equipped with
manual transmission. Pushing the “ON/OFF” but-
ton to the OFF position or turning off the ignition
erases the speed memory.
To Resume Speed:
To resume a previously set speed, push and
release the “RESUME/ACCEL” button. Resume
can be used at any speed above 40 km/h (25
mph).
To Vary the Speed Setting:
When the speed control is set, speed can be
increased by pressing and holding the “RESUME/
ACCEL” button. When the button is released, a
new set speed will be established.
Tapping the RESUME/ACCEL button once will
result in a 3 km/h (2 mph) speed increase. Each
time the button is tapped, speed increases so that
tapping the button three times will increase speed
by 10 km/h (6 mph), etc.
To decrease speed while speed control is set,
press and hold the “COAST” button. Release the
button when the desired speed is reached, and
the new speed will be set.
Tapping the “COAST” button once will result in a 2
km/h (1 mph) speed decrease. Each time the
button is tapped, speed decreases.
To Accelerate For Passing:
Depress the accelerator as you would normally.
When the pedal is released, the vehicle will return
to the set speed.
NOTE:
The speed control system maintains speed up
and down hills. A slight speed change on
moderate hills is normal.
58
Содержание Voyager 2001
