Chrysler 300 Touring RWD 2010 Скачать руководство пользователя страница 444

Страница: 444 / 574

HAZARD WARNING FLASHERS

The Hazard Warning flasher switch is located in the

center of the instrument panel between the center air

outlets.

Push the switch to turn on the Hazard Warning

flashers. When the switch is activated, all direc-

tional turn signals will flash on and off to warn oncoming

traffic of an emergency. Push the switch a second time to

turn off the Hazard Warning flashers.
This is an emergency warning system and it should not

be used when the vehicle is in motion. Use it when your

vehicle is disabled and it is creating a safety hazard for

other motorists.
When you must leave the vehicle to seek assistance, the

Hazard Warning flashers will continue to operate even

though the ignition is placed in the OFF position.

NOTE:

With extended use the Hazard Warning flashers

may wear down your battery.

IF YOUR ENGINE OVERHEATS

In any of the following situations, you can reduce the

potential for overheating by taking the appropriate ac-

tion.

•

On the highways — slow down.

•

In city traffic — while stopped, place the transmission

in NEUTRAL, but do not increase the engine idle

speed.

NOTE:

There are steps that you can take to slow down

an impending overheat condition:

•

If your air conditioner (A/C) is on, turn it off. The A/C

system adds heat to the engine cooling system and

turning the A/C off can help remove this heat.

442 WHAT TO DO IN EMERGENCIES

Содержание 300 Touring RWD 2010































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 300 Touring RWD 2010

Отзывы:

Бренды по названию

Популярные бренды

Chrysler 300 Touring RWD 2010, Руководство пользователя

Результаты поиска

Содержание 300 Touring RWD 2010

Отзывы:

Бренды по названию

Популярные бренды