Chrysler 2005 Sebring, Руководство по обслуживанию, Страница: 441 / 3204

SINGLE WARNING CHIME
After bulb check at power-up, if any of the follow-
ing indicators are still activated, the cluster will
request a single chime from the BCM. ABS, Air Bag,
Check Engine, Charging System, Engine Tempera-
ture, Low Fuel (after 10 seconds for accurate fuel
information), and BRAKE (if speed is greater than 2
mph).
DIAGNOSIS AND TESTING
DIAGNOSIS AND TESTING - CHIME
CONDITIONS
For Removal and Installation of Junction Block
(JB) (Refer to 8 - ELECTRICAL/POWER DISTRIBU-
TION/JUNCTION BLOCK - REMOVAL).
For Removal and Installation of Body Control Mod-
ule (BCM), refer to Electrical, Electronic Control
Modules, Body Control Modules, Removal, and
Installation.
NO TONE WHEN IGNITION SWITCH IS TURNED ON
AND DRIVERS SEAT BELT IS UNBUCKLED AND
FULLY RETRACTED
(1) Check driver’s seat belt retractor switch for a
ground when belt is retracted.
(2) Use DRB III
!
scan tool to perform PCI data
bus diagnostics on the BCM for battery, ignition and
seat belt switch inputs.
(3) Use DRB III
!
scan tool to perform actuator
diagnostics on BCM Chime.
(4) Check for tone in any other function.
(5) Remove BCM from Junction Block. Check for
battery voltage at terminal JB-12 and ignition feed
at terminal JB-6 of BCM (Fig. 1). Refer to the appro-
priate wiring information. The wiring information
includes wiring diagrams, proper wire and connector
repair procedures, details of wire harness routing
and retention, connector pin-out information and
location views for the various wire harness connec-
tors, splices and grounds.
(6) If voltage not OK, repair as necessary.
NO FASTEN SEAT BELT LAMP WHEN IGNITION
SWITCH IS TURNED ON
(1) At power-up, the cluster will turn ON the seat
belt warning indicator for 6 ± 1 seconds as required
regardless of the driver side seat belt buckle status.
If the warning indicator does not turn ON, verify if
the socketed red LED is seated properly and good
contact with the PC-board is present. If not seated
properly, then seat the LED properly by twisting the
socket counterclockwise. If seated properly, replace
the LED.
SEAT BELT LAMP ON FOR MORE THAN 7
SECONDS AFTER DRIVER SEAT BELT BUCKLE
SWITCH IS FASTENED AND IGNITION ON
(1) Use a DRB III
!
scan tool to verify status of the
driver seat belt buckle switch as received by the
instrument cluster. Compare to the actual seat belt
buckle status: If buckled, lamp is OFF or if unbuck-
led, lamp is ON. If the status received by the instru-
ment cluster does match the actual buckle seat belt
switch status (buckled/unbuckled), then check the
driver seat belt switch and wiring for proper connec-
tion.
NO TONE OR DOOR INDICATED IN PLACE OF
ODOMETER WHEN A DOOR IS AJAR AND VEHICLE
BEGINS MOVING
The vehicle must be moving for the chime to occur.
However the door indicator will come ON regardless
of the vehicle movement. The PCI data bus, Trans-
mission Control Module (TCM) and Powertrain Con-
trol Module (PCM) must be operational.
(1) Check all door jamb switches.
(2) Use DRB III
!
scan tool to perform PCI data
bus diagnostics on BCM for battery and ignition
switch input
(3) Inspect BCM connectors and wires for proper
connection.
Fig. 1 JUNCTION BLOCK CONNECTOR TO THE
BCM
1 - BODY CONTROL MODULE
2 - H/LP RELAY
3 - HORN RELAY
4 - EBL
5 - CIRCUIT BREAKERS
6 - HORN
8B - 2 CHIME/BUZZER
JR
CHIME/BUZZER (Continued)