background image

16

Replacement Heaters

MicroTHERM Oil Replacement Parts

kW

Voltage

Heater

6

240

052-305096-001

6

480

052-305096-002

9

240

052-305096-007

9

480

052-305096-008

12

240

052-305096-005

12

480

052-305096-006

18

240

052-305096-003

18

480

052-305096-004

24

480

052-305096-001

Replacement Parts Common to All Models

Identifi-

cation#

Part Name

Part Number

1

3 HP Pump & Motor 230V/460V

226-304843-002

2

Pump Rebuild Kit (Seal, Gasket, etc.)

251-121946-032

3

Solenoid Valve

344-072237-021

4

Safety Relief Valve

344-300032-103

5

Pressure Gauge 0-100psig

130-118661-037

6

Pressure Gauge 30” Vac - 30 psig

130-118661-038

7

Thermocouple Process T/C

Thermocouple Overtemp T/C

309-304460-036

300-304460-012

8

Push Button, Start

292-304687-003

9

Push Button, Stop

292-304687-004

10

Light, Red

213-122066-041

11

Light, Amber

213-122066-042

12

Light, Green

213-122066-043

13

Motor Contactor 240/480V

072-123534-065

14

Auxiliary Motor Contact Block

071-122886-055

15

Motor Thermal Overload 240V

359-122078-097

16

Motor Thermal Overload 480V

359-122078-096

17

Transformer 240/480V

315-303786-001

18

Caster, Swivel

375-123425-006

19

Caster, Rigid

375-123425-007

20

Control Voltage Fuse

303-123432-024

21

Heater Contactor

072-304551-008

22

Over Temperature Controller

381-700400-297

23

Fan

112-121869-005

24

SCR

300-400360-610

25

On/Off Cooling Switch

292-304687-002

Limited Warranty:

Please refer to the Chromalox limited warranty applicable to this product at

http://www.chromalox.com/customer-service/policies/termsofsale.aspx.

Chromalox, Inc.

2150 N. Rulon White Blvd.,

Ogden, UT 84404

Phone: 1-800-368-2493

www.chromalox.com

© 2019 Chromalox, Inc.

Содержание MicroTherm



















Отзывы: