background image

Digital Power Meter 66203/66204 User’s Manual

 

 

5-32 

Setting syntax:  INTEGrate<space><CRD><PMT>

 

Setting parameters: <CRD>, OFF | ON 
Query syntax:   

INTEGrate?<PMT> 

Return parameters: <CRD>, OFF | ON 

Header on: 

:INTEGRATE<space><CRD><RMT> 

Header off: 

<CRD><RMT> 

Example:  

 

none 

 
 

[CONFigure:]INTEGrate:TIME 

            

 

 

 

 

Type:     All 

channels. 

Description:   

This command sets the time of integration in Second. 

Setting syntax:  INTEGrate:TIME<space><NR1><PMT>

 

Setting parameters: <NR1>, 0 ~ 35999999 
Query syntax:   

INTEGrate:TIME?[<space><MAX | MIN>]<PMT> 

Return parameters: <NR1>, 0 ~ 35999999 

Header on: 

:INTEGRATE:TIME<space><NR1><RMT> 

Header off: 

<NR1><RMT> 

Example:  

 

none 

 
 

[CONFigure:]FILTer 

              

 

 

 

 

Type:     All 

channels. 

Description:   

This command is used to switch the low pass filter.   

Setting syntax:  FILTer<space><CRD><PMT>

 

Setting parameters: <CRD>, ON | OFF 
Query syntax:   

FILTer?<PMT> 

Return parameters: <CRD>, ON | OFF 

Header on: 

:FILTER<space><CRD><RMT> 

Header off: 

<CRD><RMT> 

Example:  

 

none 

 
 

[CONFigure:]THD:MODE 

 

 

 

 

 

 

 

 

 

 

 

 

         

Type:     All 

channels. 

Description:   

This command sets the mode of THD measure. 

Setting syntax:  THD:MODE<space><CRD><PMT>

 

Setting parameters: <CRD>, FULL | ORDER 
Query syntax:   

THD:MODE?<PMT> 

Return parameters: <CRD>, FULL | ORDER 

Header on: 

:THD:MODE<space><CRD><RMT> 

Header off: 

<CRD><RMT> 

Example:  

 

none 

 
 

[CONFigure:]THD:ORDer   

 

 

 

 

 

 

 

 

 

 

 

         

Type:     All 

channels. 

Description:   

This command sets the order of THD measure.   

Setting syntax:  THD:ORDer<space><NR1><PMT>

 

Setting parameters: <NR1>, 2 ~ 100 
Query syntax:   

THD:ORDer?[<space><MAX | MIN>]<PMT> 

Return parameters: <NR1>, 2 ~ 100 

Header on: 

:THD:ORDER<space><NR1><RMT> 

Header off: 

<NR1><RMT> 

Содержание 66203



















































































































































Отзывы: