Christini AWD 450E Скачать руководство пользователя страница 115 | Manualshive

Страница: 115 / 118

background image

Page 114

CHRISTINI AWD LI MITED WARRANTY

This LIMITED WARRANTY is a complete and ex clusive statement of CHRISTINI’s obligations to the
ORIGINAL OWNER of a CHRISTINI AWD Motorcycle.

CHRISTINI Technologies warrants:

-ONLY T he All Wheel Drive Components of the CHRIST INI AWD 450E Competition use Motorcycle and all other
original CHRISTINI AWD components, including the fork machined parts, front hub, gear box, and the components of
the CHRIST INI All Wheel Drive (AWD) system including shafts and drive gears are warranted to be free o f defects in ma-
terial and workmanship for a period of ONE (1) year from the date o f Purchase for the Original Owner.

OTHER ORIGINAL COMPONENTS

Any components not produced by CHRIST INI, including the front suspension fork intern al mechanisms, bear their original
manu factu rer’s own warranty and CHRIST INI reserv es the right to direct any warranty requ est relating to those Other
Original Components to said manufacturer’s customer service dep artment.

THESE WARRANTIES DO NOT COVER:

•

Failures or required services which are not due to a defect in material or factory workmanship.

•

Replacement o f expend able maintenan ce items including, but not limited to:

•

Bearings, including linear bearing

•

Seals and O-Rings

•

AWD Clutch Basket, Plates, and Friction Plates

•

Shaft Bellows

•

AWD Engagement cable and housing

•

Sprockets and Drive Chains

•

Parts or accessories affected or damaged by:

•

Normal wear

•

Finish, including frame, anodized machine parts, and coatings on gears, sprockets and driveshafts

•

Improper maintenan ce including improper clutch settings

•

Lack o f proper mainten ance

•

Improper installation

•

Deterioration from exposure to the elements

•

T he unauthorized alteration of any part

•

T he incorporation or use of unsuitable attachments or parts

•

Unsuitable use in an application for which the part was not designed

•

Neglect

•

Misuse

•

Abuse

•

Vandalism

Failures caused by or related to any modification not approved by Christini T echnologies, Inc.

•

Failures caused by or related to any installation of any parts or kits designed for “competition only” use

•

Use for the following activities: which will VOID these warranties:

•

Racing

•

Competition

•

Rental

Warranty

«
...
113
114
115
116
117
...
»

Содержание AWD 450E























































































































Отзывы:

Нет отзывов

Похожие инструкции для AWD 450E

Бренд: Cake Страницы: 13

Бренд: KYMCO Страницы: 58

Soft Luggage Pannier Racks

Бренд: Honda Страницы: 10

Бренд: LAZER Страницы: 19

Бренд: Kong Страницы: 72

Бренд: MV Agusta Страницы: 36

Бренд: Baja motorsports Страницы: 20

Бренд: Fantic Motor Страницы: 145

Бренд: Suzuki Страницы: 42

2007 enducross EC

Бренд: GAS GAS Страницы: 72

GM STAR 250 1986

Бренд: Maico Страницы: 32

Бренд: National Cycle Страницы: 2

Бренд: Peugeot Motorcycles Страницы: 52

Бренд: VM Страницы: 2

Бренд: Innovv Страницы: 2

Бренд: Sealey Страницы: 2

Бренд: Bagster Страницы: 2

Бренд: Baotian Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды