Christini AWD 450E Скачать руководство пользователя страница 10

Страница: 10 / 118

Page 9

Basic Operating Instructions

PRECAUTION

For your safety, you must obey the following 9 rules while riding the motorcycle:

- Wear your helmet: Safe ride begins with putting on helmet. You must wear helmet while riding.

- Wear simple and convenient clothes. Pay attention to avoid wearing loose clothing. Please wear tight and

closed clothes to ensure that your hands and feet move freely.

- Check the pre-ride inspection before riding: Always check before starting the engine.

- Get familiar with the assembly and performance of this motorcycle

-Your riding skills and knowledge of this motorcycle are the basis of safe riding. You should practice riding

in an open area without vehicles to master riding skills.

- Get to know the speed limit of safe riding

-The motorcycle’s safe riding speed depends on the ground condition and your riding skills. Knowing the

speed limit based on your riding ability can avoid accidents.

- Do not ride after drinking or taking medicine.

- This bike is designed for adult operators only. Be sure you are allowed to ride this kind of motorcycle

based on your local laws.

- Pay special attention to riding in rain

-Riding on wet roads is very dangerous. Turn during acceleration and a keep safe distance from vehicles in

front of your motorcycle. Remember that the braking distance in rain is twice of that in sunny days, and
please pay special attention to traffic signs. Once the condition of the road changes, reduce your speed.

-Exhaust gas contains harmful substance such as carbon monoxide. Only start the engine in well-ventilated

places.

Содержание AWD 450E























































































































Результаты поиска

Содержание AWD 450E

Отзывы:

Похожие инструкции для AWD 450E

Бренды по названию

Популярные бренды

Christini AWD 450E, Руководство по обслуживанию

Результаты поиска

Содержание AWD 450E

Отзывы:

Похожие инструкции для AWD 450E

Бренды по названию

Популярные бренды