Christie Mirage 4K35 Скачать руководство пользователя страница 25

Страница: 25 / 103

Installation and Setup

Mirage 4K35 User Manual

020-101377-03 Rev. 1 (07-2015)

Install the lamp power supply in a rack stand

1. Remove the right (operator's side) panel of the rack stand.

2. Remove the cross bar.

3. Insert the lamp power supply (LPS) support into the rack stand and align the pins with the

holes.

4. Lift the LPS into the frame.

5. Remove the bottom 10 panels from the back of the rack stand.

6. Assemble the three-piece airflow duct (supplied with LPS). First snap the two L shaped parts

together, and then snap this into the six stand out pins of the third piece (flat panel).

7. Position the airflow duct directly behind the LPS.

8. Insert airflow duct into rack stand from the outside.

9. Secure airflow duct to rack stand using screws from the rack stand panels.

Do not install any components in front of the lamp power supply that will restrict airflow.

Содержание Mirage 4K35








































































































Результаты поиска

Содержание Mirage 4K35

Отзывы:

Похожие инструкции для Mirage 4K35

Бренды по названию

Популярные бренды

Christie Mirage 4K35, Руководство пользователя

Результаты поиска

Содержание Mirage 4K35

Отзывы:

Похожие инструкции для Mirage 4K35

Бренды по названию

Популярные бренды