Christ 112991 Скачать руководство пользователя страница 111 | Manualshive

Страница: 111 / 148

background image

Freeze-dryer Epsilon 1-4 LSCplus

Freeze-dryer Epsilon 2-4 LSCplus

7 Malfunctions and error correction

Version 04/2014, Rev. 2.13 of 01/12/2021

• sb

111 / 148

Translation of the original operating manual

Pos : 222 /200 Chris t/360 GT-BA Labor-Pil ot ( STAND ARDMO DULE)/070 St örungen und F ehl ersuche/ 070- 0010- 0020-0020 Bel üft ungsventil (z. B. E2-4) @ 25\mod_1404984751036_68. doc x @ 186099 @ 4 @ 1

→

7.1.2.2

Aeration valve

A malfunction of the aeration valve may have several causes. One
potential source are contaminants such as product residues within the
valve.
•  Switch the freeze-dryer off and disconnect the mains plug.
•  Clean the valve (see chapter 8.1.3 - "Aeration valve").
•  Put the freeze-dryer into operation again.
If there is still a leakage, the freeze-dryer must be checked by qualified
specialist personnel (see chapter 7.3 - "Service contact").

Pos : 223 /010 Univ ers almodul e/ Leerz eile @ 0\mod_1202116244500_0.docx @ 114 @ @ 1

Pos : 224 /200 Chris t/360 GT-BA Labor-Pil ot ( STAND ARDMO DULE)/070 St örungen und F ehl ersuche/ 070- 0010- 0020-0025 Druckst euerv entil @ 25\m od_1404984063525_68. docx @ 184209 @ 4 @ 1

→

7.1.2.3

Pressure control valve

A malfunction of the pressure control valve may have several causes.

NOTE

The inspection of the valve must be carried out by qualified specialist
personnel (see chapter 7.3 - "Service contact").

Pos : 225 /010 Univ ers almodul e/ Leerz eile @ 0\mod_1202116244500_0.docx @ 114 @ @ 1

Pos : 226 /200 Chris t/360 GT-BA Labor-Pil ot ( STAND ARDMO DULE)/070 St örungen und F ehl ersuche/ 070- 0010- 0020-0030 G ummiv entile @ 25\mod_1404984064588_68. doc x @ 184223 @ 4 @ 1

→

7.1.2.4

Rubber valves

In order to identify a leaking rubber valve, the valves must be checked
individually:
• Remove the rubber valve and seal the connection at the drying

chamber with a rubber stopper.

• Check the tightness under vacuum until the leaking valve has been

localised.

• Clean the valve or replace it if necessary.

Pos : 227 /010 Univ ers almodul e/ Leerz eile @ 0\mod_1202116244500_0.docx @ 114 @ @ 1

Pos : 228 /200 Chris t/360 GT-BA Labor-Pil ot ( STAND ARDMO DULE)/070 St örungen und F ehl ersuche/ 070- 0010- 0020-0040 Vak uummess sonde @ 25\mod_1404984065691_68. docx @ 184237 @ 4 @ 1

→

7.1.2.5

Vacuum sensor

Vacuum sensors have a limited service life and can be ordered as spare
parts.

Capacitive vacuum sensors

Capacitive vacuum sensors may experience a measurement drift due to
long-term use, soiling or sudden aeration. In this case, the vacuum sensor
must be adjusted (see chapter 8.1.9 - " Vacuum sensor ").

Pos : 229 /010 Univ ers almodul e/ Seit enwechs el @ 0\mod_1202116244312_0.docx @ 105 @ @ 1

«
...
109
110
111
112
113
...
»

Содержание 112991





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для 112991

Бренд: zipwake Страницы: 2

Бренд: zipwake Страницы: 2

Бренд: Walker Bay Страницы: 8

Бренд: Xoop Lighting Страницы: 20

Бренд: Vari Lite Страницы: 132

Бренд: idiag Страницы: 12

Бренд: Eazyzap Страницы: 32

Бренд: Obdstar Страницы: 42

Бренд: K-9 Lights Страницы: 12

Бренд: K'Nex Education Страницы: 2

Бренд: Keller Страницы: 12

Бренд: MacDon Страницы: 49

Бренд: MacDon Страницы: 49

Бренд: MacDon Страницы: 4

Бренд: NARGESA Страницы: 37

Бренд: NARGESA Страницы: 6

Бренд: QRS Страницы: 16

Бренд: QMAXZ Lighting Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды