Chiltrix CX34 Скачать руководство пользователя страница 56

Страница: 56 / 61

Chiltrix Inc.

www.chiltrix.com

low pressure protection

(1) less refrigerant; (2) throttle failure; (3) low-voltage
switch failure

compressor overheat protection

(1) less refrigerant; (2) throttle mechanism failure

over current protection Verify that
P88 = 4

(1) too much refrigerant; (2) throttle mechanism
failure; (3) current sensor failure

indoor unit water flow error

(1) water flow is too small; (2) water switch failure

outdoor water flow error

(1) water flow side is too small; (2) water source side
of the water flow switch failure

miss phase

Power failure

wrong phase

Power failure

communication error

The communication line is broken or the control board
is damaged

P10

water source anti-freeze

(1) the water source side of the heat transfer or water
temperature is too low; (2) water side of the water
flow is insufficient

P11

water source water flow not enough

(1) water side of the water flow is low

P12

EPPRON initializes the fault

P13

Control board and inverter communication
fault

(1) The inverter and the circuit board communication
line is loose (2) inverter fault

P14

The temperature difference between inlet
and outlet is too large

(1) water flow is too small; (2) water switch failure

P15

Current limit frequency fault

Caused by current limitation at lubricant oil return
operation. Set P33=6°C

voltage protection

Power voltage is too high or too low, the voltage is
normal after the machine to resume operation
(motherboard detection)

IPM Fault

IPM module is damaged

Compressor Drive Fault

The compressor cannot start normally

Compressor over current protection 1

IPM detects that the compressor current is excessive
(IPM or compressor or wiring is faulty)

Compressor over current protection 2

The motherboard detects that the compressor current
is excessive

IPM Overheat

IPM temperature exceeds the set value

PFC Fault

PFC damage

DC bus over voltage

DC voltage exceeds 410V

DC bus under voltage

DC voltage less than 200V

F10

AC input over or under voltage

Power voltage is too high or too low, the voltage is
normal after the machine to resume operation (IPM
detection) (175V ~ 255V)

F11

AC input overcurrent

IPM detected AC current exceeded

F12

Temperature sensor Fault

temp sensor is open or shorted

F13

DSP and motherboard communication Fault

Communication break or control board failure

F14

EC fan failure 1

EC fan 1 not connected or fan failure

F15

EC fan failure 2

EC fan 2 not connected or fan failure

Содержание CX34






























































Результаты поиска

Содержание CX34

Отзывы:

Похожие инструкции для CX34

Бренды по названию

Популярные бренды

Chiltrix CX34, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CX34

Отзывы:

Похожие инструкции для CX34

Бренды по названию

Популярные бренды