Chicco OASYS 2/3 FixPlus, Инструкция по эксплуатации

Страница: 18 / 24

18
in relation to the lower section of the child
car seat (Diag. 3). In this case the child car
seat must not be installed on that specific
seat, and you should try installing it on a
seat that does not have this inconvenience.
Please contact the car manufacturer for
further information on this aspect.
• The child car seat can be fitted into the
front passenger seat or any other back
seats, always in a forward facing direction.
Never use this child car seat on vehicle
seats which are facing sideways or
rearwards (diag. 4)
WARNING! According to car accident
statistics, the rear seats of a vehicle are
generally safer than the front seat: it is
therefore recommended to fit the child
car seat into the rear seats of the car. In
particular, the central rear seat is the safest,
when fitted with a 3-point safety strap: in
this case it is recommended to fit the child
car seat onto the central rear seat of the
vehicle.
If the child car seat is fitted in the front seat
of the car, in order to ensure maximum
safety, it is recommended to push the seat
back as much as possible, bearing in mind
the comfort of the passenger sitting in the
seat directly behind it and adjusting the
backrest to the most vertical position. If the
vehicle is fitted with an adjuster to regulate
the height of the safety belt, position it as
low as possible. Check that the safety belt
adjuster is behind (or at the most aligned)
with the backrest of the vehicle seat (Diag.
5A and 5B).
It is not recommended to fit the child car
seat into a front seat equipped with airbag.
If you wish to fit the child car seat in any
seat protected by airbag, always refer to
the vehicle instructions manual. Make sure
that the buckle seat belt is not too high
and not rests on the armrest of the car seat
(Diag 3). Otherwise, try to install the car
seat for your child on another car seat in
the car.
INSTRUCTIONS FOR USE
Contents
• Fitting the child car seat inside the vehicle
using safety belts and placing the child
inside
• Fitting the child car seat inside the vehicle
using safety belts and rigid FixPlus clasps
and placing the child inside
• Installing the child seat inside the vehicle
without the child inside
• How to remove the child from the child
car seat
• Removal of the child car seat from the
vehicle
• Installing and removing the cup holder
• Adjusting the height of the back rest
• Adjusting the width of the back rest
• Adjusting the inclination of the child car
seat backrest/seat
• Removable backrest/seat covers
• Cleaning and maintenance of the seat
covers
Parts
A. Headrest
B. Diagonal belt guide
C. Backrest
D. Armrests
E. Seat
F. Lap belt guide
G. Cup holder
H. Reclining adjuster button
I. Safety belt guide open/close button
J. Cup holder clip
K. Backrest width adjuster wheel
L. Backrest height adjuster lever
M. Rear pocket for instruction booklet
N. Side wings
O. Rigid FixPlus clasp lever
P. Rigid clasps
Q. Indicators
R. Rigid clasp release system buttons
Fitting the child car seat inside the
vehicle using safety belts and placing
the child inside
WARNING! These instructions and
diagrams are for the installation of the child
car seat on the right back seat.
To fit the child car seat in other positions,
carry out these operations in the same
order.
1. Place the child car seat onto the vehicle
seat with the backrest up against the
vehicle seat
backrest
WARNING! Check that the vehicle headrest
does not interfere with the child seat
headrest: it must not push it forwards (Diag.
6). If this happens, remove the headrest
from the vehicle seat where you intend
to install the child car seat. Remember to
replace the vehicle headrest when the
child car seat is removed and a passenger
uses the seat.
WARNING! The rear side of the child car
seat must be resting against the vehicle
seat.
2. Place your child inside the car seat
with his back correctly placed against the
backrest.
3. Check the backrest height (see
paragraph “ADJUSTING THE HEIGHT OF
THE BACKREST”)
4. Check the backrest width (see
paragraph “ADJUSTING THE WIDTH OF THE
BACKREST”)
5. Thread the diagonal car seat belt
through the diagonal belt guide (B). Check
that the belt guide (l) open/close button is
firmly closed; you must be able to see the
white reference line (Diag. 7).
6. Connect the car safety belt by threading
the lap belt trough the red lap belt guides
(F) under the two armrests in line, and by
threading the diagonal belt under the
armrest on the side of the fastener buckle
(Diag. 8).
7. Pull the diagonal car safety belt upwards,
19