Chicco OASYS 2/3 FixPlus, Инструкция по эксплуатации

Страница: 20 / 24

20
1. Place the child car seat onto the vehicle
seat with the backrest up against the
vehicle seat
backrest (diag. 12)
WARNING! Check that the vehicle headrest
does not interfere with the child seat
headrest: it must not push it forwards
(Diag. 6). If this happens, remove the car
seat headrest. Remember to replace the
vehicle headrest when the child car seat
is removed and a passenger uses the seat.
2. Pull the lever (O), located under the
inclination adjuster button (H), upwards.
(Diag. 13)
3. While keeping the lever pulled, pull out
the rigid clasps (P) completely from the
rear of the backrest (diag. 14).
4. Insert the two rigid clasps (P) into the
corresponding ISOFIX anchorage points on
the car seat, located between the backrest
and the seat (diag. 15).
WARNING! Check that the two indicators
(Q) are green which means the system has
been installed correctly (diag.16).
5. Push the child car seat firmly against
the backrest of the car seat (Diag. 17),
pushing the lever (O) to ensure maximum
adherence of the child car seat backrest
against the car seat.
6. Sit the child inside with his back against
the child car seat backrest and follow the
instructions 3-4-5-6-7 provided in the
previous chapter to install the car safety
belts, (Fitting the child car seat inside the
vehicle using safety belts and rigid FixPlus
clasps and placing the child inside) paying
attention to every single detail.
The rigid FixPlus clasps are designed to
improve the levels of comfort and stability
of the child car seat. It is possible to use
the Oasys FixPlus child car seat without
these optionals, if you encounter problems
installing them in your car.
Installing the child seat inside the
vehicle without the child inside
When the child is not travelling in the car,
the child car seat should be left secured
by the vehicle three-point safety belt, or
stowed away in the car boot. An unsecured
child car seat may be a source of danger
for the other passengers in the event of an
accident or sudden braking.
How to remove the child from the child
car seat
Release the car belt buckle, accompanying
the belt as it retracts.
Removal of the child car seat
WARNING! Remove the child from the
child car seat before removing it.
1. Release the car safety belt.
2. Unthread the diagonal strap through the
guide, accompanying it as it retracts.
If the rigid clasps have been used to fasten
the car seat in place, they must now be
released from the anchor points:
1. Pull the two red buttons on the rigid
clasp release system towards you, release
the clasps from the corresponding Isofix
anchor points on the car seat (Diag. 18) so
that the indicator is completely red.
2. Hold the lever up (O) as you push the
rigid clasps all the way into the base of the
child car
seat, (Diag. 19).
Installing and removing the cup
holder
The child car seat has 2 inserts, one on
the right and one on the left of the side of
the seat where you can fit the cup holder
whenever you like.
To install the cup holder:
1. Insert the cup holder into the relative
guide (Diag. 20)
2. Press the cup holder downwards until it
clicks into place (Diag. 21).
WARNING! Do not place glass containers or
21
hot liquids on the cup holder as they could
harm the child.
To remove it:
1. Press the lever on the back of the cup
holder and lift it upwards, out of the guide
(Diag. 22)
The cup holder guides are fitted with a
special device that makes sure it always
remains in a horizontal position.
To rotate and position the cup holder:
1. Press the lever on the back and rotate it
to the desired position
Adjusting the height of the back rest
The height of the headrest can be adjusted
to 10 different positions to adapt the child
car seat to
the height of the child.
Make sure the child’s head is always well
protected and the car diagonal safety belt
is positioned
properly on his shoulder.
When adjusting the height of the backrest,
check that the diagonal belt loop (B) is
positioned at
a maximum of 2 cm above the child’s
shoulder (Diag. 23)
To make the adjustment:
1. Use one hand to press the child car seat
backrest height adjuster lever (L) located
on the back of the headrest (Diag. 24)
2. Raise/lower the backrest to adapt it to
the height of the child’s shoulders (Diag.
25)
3. Release the lever checking that it has
clicked into the desired position.
Adjusting the width of the back rest
The width of the backrest can be adjusted
to adapt the child car seat to suit the
physique of
the child. Use the backrest width regulator
wheel (K) located above the headrest, to
adjust the width: