background image

SKU 99823 

For technical questions, please call 1-800-444-3353. 

Page 2

saVe this Manual

Keep this manual for the safety 

warnings and precautions, assembly, 

operating, inspection, maintenance and 

cleaning procedures.  Write the product’s 

serial number in the back of the manual 

near the assembly diagram (or month 

and year of purchase if product has no 

number).  Keep this manual and the 

receipt in a safe and dry place for future 

reference.

iMportant saFety 

instructions

in this manual, on the labeling, 

and all other information 

provided with this product:

  this is the safety alert 

symbol.  it is used to alert 

you to potential personal 

injury hazards.  obey all 

safety messages that 

follow this symbol to avoid 

possible injury or death.

 

danger indicates 

a hazardous 

situation which, if not 

avoided, will result in death or 

serious injury.
 

Warning 

indicates a 

hazardous situation which, if 

not avoided, could result in 

death or serious injury.

 

caution, used 

with the safety 

alert symbol, indicates a 

hazardous situation which, if 

not avoided, could result in 

minor or moderate injury.
 

notice is used to 

address practices 

not related to personal injury.
 

caution, without 

the safety alert 

symbol, is used to address 

practices not related to 

personal injury.

read and understand all 

instructions

When using electrical tools, 

safety precautions should 

always be followed including the 

following:

Work area safety

Do not use outdoors.

1. 

Close supervision is necessary when 

2. 

any tool is used by or near children.
Do not let cord hang over edge 

3. 

of table or counter, or touch hot 

surfaces.
Do not place on or near a hot gas or 

4. 

electric burner, or in a heated oven.
Extreme caution must be used when 

5. 

moving an tool.
Keep the work area well lit.  Make 

6. 

sure there is adequate surrounding 

workspace.  Keep the work area free 

of obstructions and other debris.

Содержание 99823













Отзывы: