background image

SKU 92476           For technical questions, please call 1-800-444-3353.

PAGE 9

8.

IMPORTANT:  When the YELLOW Light illuminates on the LED Display (3),
immediately turn off the Power System and recharge the Battery.  Operating the
Power System with the YELLOW Light illuminated may result in damage to the
Battery.  (See Figure B.)

9.

NOTE:  The Lights on the LED Display
(3) indicate the following:
(See Figure B.)

FIGURE B

To Power 12 VDC Tools And Appliances:

1.

The Power System may be used to power various 12 VDC small power tools and
appliances (i.e., 12 VDC drills, screwdrivers, cellphones, televisions).

2.

To power a 12 VDC power tool or appliance, insert the 12 VDC Cigarette Lighter
Plug (12) into a 12 VDC Output (4).  Insert the other end of the 12 VDC Cigarette
Lighter Plug into the power input of the tool or appliance.  Then, turn the Power
Switch (2) to its “ON” position.  (See Figure A.)

3.

When finished using the 12 VDC tool or appliance, unplug the 12 VDC Cigarette
Lighter Plug (12) from the 12 VDC Output (4).  Unplug the other end of the
12 VDC Cigarette Lighter Plug from the power input of the tool or appliance.
Then, turn the Power Switch (2) to its “OFF” position.  (See Figure A.)

4.

As soon as possible, recharge the Power System.

To Power 3 VDC, 6 VDC, And 9 VDC Tools And Appliances:

1.

Determine what voltage your tool or appliance operates on.

2.

Use a dual modular connection cord (not included) to attach the tool or appliance
to either the 3 VDC Output (5), 6 VDC Output (6), or 9 VDC Output (7).  NOTE: a
dual modular connection cord may be purchased at your local electronics
supplier, if one is not included with the tool or appliance.  (See Figure A.)

3.

CAUTION!  Make sure to use the correct Power System Output (5, 6, 7) to
power those devices whose voltage match those of the Output.

To Operate The Emergency Light:

The Power Switch (2) controls the Emergency Light (10).  Turn the Power Switch
to its “ON” position to turn on the Emergency Light.  Turn the Power Switch to its
“OFF” position to turn off the Emergency Light.  (See Figure A.)

GREEN - FULL CHARGE (ON)

RED - CHARGING

YELLOW - LOW BATTERY

GREEN - CHARGING (FULL)

Содержание 92476











Отзывы: