background image

SKU 92476           For technical questions, please call 1-800-444-3353.

PAGE 6

SAVE THESE  INSTRUCTIONS

23.

        WARNING!   The warnings and precautions discussed in this manual
cannot cover all possible conditions and situations that may occur.  It must be
understood by the operator that common sense and caution are factors which
cannot be built into this product, but must be supplied by the operator.

22.               WARNING!   People with pacemakers should consult their physician(s)

before using this product.  Electromagnetic fields in close proximity to a heart
pacemaker could cause interference or failure of the pacemaker.  In addition,
people with pacemakers should adhere to the following:  Avoid operating power
equipment alone.  Don’t use a power equipment with the power switch(es) locked
on.  Properly maintain and inspect all power equipment before use to avoid elec-
trical shock.

21.               WARNING!   The user should never attempt to replace the internal

Battery.  Battery replacement should only be done by a qualified service
technician.

gen gas is explosive, poisonous to breathe, and highly flammable.  Only charge a
battery in a well ventilated area.

17.

Always wear eye protection.  When working on or around lead acid batteries,
always wear ANSI approved safety impact eye goggles.

18.

              Use the Power System in a well ventilated area.  If necessary, wear

   an ANSI approved breathing respirator to avoid hydrogen gas fumes.

19.

Proper Battery Care: Battery leakage may occur under extreme usage or
temperature conditions.  If Battery fluid comes in contact with skin, wash with
soap and water and rinse with lemon juice and vinegar.  If the fluid comes into
contact with the eyes, flush with water for several minutes and contact a doctor
immediately.  Never burn the Battery, as it can explode in a fire.  Do not charge
the Power System with a leaking Battery.  Contact local solid waste authorities for
instructions on correct disposal or recycling of the Battery.

20.

Always recharge the Battery when Power System performance begins to
diminish.
  Severe heat is most destructive to the Battery.  The more heat
generated, the faster the Battery loses power.  A Battery that gets too hot can be
permanently damaged.  Never over-discharge the Battery by using the Power
System while its performance is decreasing.  Never attempt to discharge the
Battery by continuing to use the Power System.  When the YELLOW Light illu-
minates on the Power System, turn off the Power System, recharge the
Battery, and use the fresh Battery for optimal performance.

Содержание 92476











Отзывы: