background image

6.

If you are using an extension cord outdoors, make sure it is marked with the
suffix “W-A” (“W” in Canada) to indicate it is acceptable for outdoor use.

7.

Make sure your extension cord is properly wired and in good electrical condition.
Always replace a damaged extension cord or have it repaired by a qualified
electrician before using it.

8.

Protect your extension cords from sharp objects, excessive heat, and damp or
wet areas.

SKU 90814

PAGE 9

SYMBOLOGY

Double Insulated

Canadian Standards
Association

Underwriters
Laboratories, Inc.

Volts Alternating Current

Amperes

No Load Revolutions
per Minute (RPM)

no

xxxx/min.

A

V ~

RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS*

     25 FEET

   50 FEET        75 FEET         100 FEET         150 FEET

       0 - 2.0

18

         18

     16

   16

  16

      2.1 - 3.4

18

         18

     16

   14

  14

      3.5 - 5.0

18

         18

     16

   14

  12

      5.1 - 7.0

18

         16

     14

   12

  12

      7.1 - 12.0

18

         14

     12

   10

   -

      12.1 - 16.0

14

         12

     10

    -

   -

      16.1 - 20.0

12

         10

      -

    -

   -

(120 VOLT)

NAMEPLATE
AMPERES
(At Full Load)

EXTENSION CORD LENGTH

FIGURE C

*Based on limiting the line voltage drop
to five volts at 150% of the rated amperes.

Содержание 90814














Отзывы: