Chevrolet MONTE CARLO 2005 Скачать руководство пользователя | Manualshive

Страница: 117 / 396

background image

Turn Signal/Multifunction Lever

The lever located on the left side of the steering column
includes the following:

•

Turn Signal and Lane-Change Signals

•

Headlamp High/Low-Beam Changer

•

Flash-to-Pass Feature

•

Windshield Wipers

•

Windshield Washer

For information on the exterior lamps, see “Exterior
Lamps” later in this section.

Turn and Lane-Change Signals

The turn signal has two upward (for right) and
two downward (for left) positions. These positions allow
you to signal a turn or a lane change.

To signal a turn, move the lever all the way up or down.
When the turn is finished, the lever will return
automatically.

An arrow on the instrument
panel cluster will flash in
the direction of the
turn or lane change.

To signal a lane change, raise or lower the lever until
the arrow starts to flash. Hold it there until you complete
your lane change. The lever will return by itself when
you release it.

If the arrow flashes faster than normal as you signal a
turn or a lane change, a signal bulb may be burned
out and other drivers won’t see your turn signal.

If a bulb is burned out, replace it to help avoid an
accident. If the arrows don’t go on at all when you signal
a turn, check for burned-out bulbs and then check the
fuse. See Fuses and Circuit Breakers on page 5-97.

3-7

«
...
115
116
117
118
119
...
»

Содержание MONTE CARLO 2005













































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MONTE CARLO 2005

2013 C-Class Coupe

Бренд: Mercedes-Benz Страницы: 388

Бренд: Standby Страницы: 10

Бренд: FORM FIT Страницы: 2

Бренд: Axxess Страницы: 8

Бренд: femkes Страницы: 7

Бренд: Hummer Страницы: 502

Бренд: Saab Страницы: 12

Бренд: METRON Страницы: 4

Electra 225 1965

Бренд: Buick Страницы: 914

Бренд: Yakima Страницы: 12

Бренд: FALCON RIDGE Страницы: 6

Бренд: Guidosimplex Страницы: 8

Бренд: Softride Страницы: 4

Бренд: Vangear Страницы: 5

Бренд: Safe Fleet Страницы: 20

Бренд: Ferve Страницы: 28

Бренд: Buick Страницы: 161

Бренд: Whispbar Страницы: 77

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды