background image

TM-G702A 

Rev.: D,  4-30-15,  DCR# 15-0423

                 

Federal Identification Code: 11815                              

© 2015 Cherry Aerospace

 

       

                    Page 

9

 

 

PART LIST FOR G702A 

ITEM PART 

No 

DESCRIPTION 

QTY 

702-054 (G702A RIVER ASSEMBLY) 

702B15 SUB-ASSEMBLY, HEAD 

 

1 702C2  SUB 

-ASSEMBLY, HEAD CYCLINDER

2 P-653  O-RING 

(.691, .551, .070)

3 P-883  RING, BACK-UP (.686, .580, .053)

4 702B16 PISTON, HEAD

5 P-216  RING, QUAD (.880, .674, .103)

6 P-209  RING, BACK-UP (.864, .688, .088)

7 P-654  O-RING 

(.879, .739, .070)

8 P-112  O-RING 

(.504, .364, .070)

9 P-848  O-RING 

(.941, .801..070)

10 702B17  CAP 

11 P-880  RING, RETAINING (NON-STANDARD)

12 703A13  FITTING, DEFLECTOR

13 530A16  DEFLECTOR, PIN

14 P-572  STAT-O-SEAL (.430, .180, .125)

15 P-573  SCREW, BUTTON HEAD SOC., 10-32 X 1/4

702-053 SUB-ASSEMBLY, HANDLE 

 

16 P-838  O-RING (.568, .362, .103)**

17 P-115  RING, BACK-UP (.551, .375, .088)

18 P-727  O-RING (1.318, 1.112, .103)

19 700B93  PLUG, PACKING

20 P-893  O-RING (2.387, 2.109, .139)

21 700A21  WASHER 

22 747-013 PISTON, AIR

23 P-1387  WASHER, STEEL

24 P-737  NUT, CONELOK, 1/4-20

25 747-015 BASE, HANDLE

26 P-894  O-RING (2.254, 2.114, .070)

27 P-895  RING, RETAINING (INT. 0 2.440)

28 P-1386  RING, RETAINING (EXT. 0 2.062)

29 747-011 COVER, URETHANE BASE

30 703A33  SUB-ASSEMBLY, TRIGGER

 31 

 

P-223 

O-RING 

(.285, .145, .070)

32 747-018 HANDLE 

33 747-019 CYLINDER, POWER

34 P-833  O-RING, DISOGRIN (1.068, .862, .103)

35 P-919  RING, BACK-UP (.528, .422, .053)

36 P-829  O-RING, DISOGRIN (.504, .364, .070)**

37 747-017 PISTON, POWER

38 700B73  SLEEVE, VALVE

39 700A67  SPRING 

40 700A15  SUB-ASSEMBLY, VALVE SPOOL

 

41 700D15-2 SPOOL, VALVE***

42 700A18  FILTER***

43 700A69  SCREW, METERING***

44 P-834  O-RING (.816 .676, .070)**

45 700A16  PLUG, VALVE

46 700A17  MUFFLER 

47 P-279  RING, RETAINING (INT. 0.906)

48 P-832  O-RING (.379, .239, .070)**

49 702A22  GASKET 

50  P-27 

SCREW, SOC. HD. CAP, 8/32 X 1/2

51 670 

037-1 ASSEMBLY, MANDREL CATCHER BAG*

52 P-948 

HOSE 

53 P-1505 

PRE-SET IN-LINE PRESSURE REGULATOR 

 

*Not furnished with riveter; must be ordered separately if desired. 
**No substitutions. 
***These parts cannot be ordered separately, but must be ordered as a sub-assembly.

 

Содержание G702A













Отзывы: