Chauvin Arnox C.A 6165 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 40

background image

9

In pre-test a too high external voltage was detected between
ISO/SUB and PE terminals. The measurement was cancelled. Press

OK

to continue.

In pre-test a possible high leakage current was detected. It is likely
that a dangerous leakage current (higher than 3.5 mA) will flow after
applying power to the device under test.

Select

YES

to proceed with or

NO

to cancel measurement.

The measured leakage (Idiff, Ipe, Itouch) current was higher than 20
mA. Measurement was aborted. Press

OK

to continue.

The load current exceeded the highest upper limit of 10 A for the
Discharging time test. Measurement was aborted. Press

OK

to

continue.

The load current continuously exceeded 10 A for more than 4 min
(moving average) in Power and Leakage tests. Measurement was
stopped for safety. Press

OK

to continue.

The load current exceeded the highest upper limit of 16 A for the
Power and Leakage tests. Measurement was aborted. Press

OK

to

continue.

Warning for restart of the instrument to set new Ethernet settings.
This message appears on exit from Settings menu after changing
Ethernet settings. Press

OK

to continue.

The instrument is overheated. The measurement can’t be carried out
until the icon disappears. Press

OK

to continue.

The device under test should be switched on (to ensure that the
complete circuit is tested).

Test voltage in Insulation resistance measurement is too low.

Measurement result is scaled to 110 V.

«
...
7
8
9
10
11
...
»

Содержание C.A 6165









































Отзывы:

Нет отзывов

Похожие инструкции для C.A 6165

Бренд: Zico Страницы: 19

Бренд: Velleman Страницы: 22

Бренд: Vorel Страницы: 88

Бренд: Telect Страницы: 124

Бренд: MARTINDALE Страницы: 2

Бренд: Raisecom Страницы: 24

Бренд: UEi Страницы: 12

Бренд: Major tech Страницы: 16

Бренд: Iso-Tech Страницы: 14

Бренд: IDEAL Страницы: 20

Бренд: Acer Страницы: 12

Бренд: Mastech Страницы: 17

Бренд: RGK Страницы: 19

Бренд: Positron Страницы: 2

Бренд: Positron Страницы: 2

Бренд: Positron Страницы: 24

Бренд: Positron Страницы: 31

Бренд: Matco Tools Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды