Chauvet Stage Designer 50 TFX-48B Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 24

Chauvet Stage Designer 50 TFX-48B Скачать руководство пользователя страница 16

Stage Designer™ 50 User Manual

16

Revised: 2008-08-25 16:16:53

Midi Operation

The controller will only respond to MIDI commands on the MIDI channel that it is assigned to. All MIDI

control is performed using Note on commands. All other MIDI instructions are ignored. To stop a

chase, send the

blackout on

note.

Setting MIDI IN

Action



1)

While holding down the

RECORD

button,

simultaneously tap Flash button #1 three
times. The display reads MIDI CHANNEL
IN to indicate channel setup is available.

2)

Select the MIDI control channel (1~16) by
tapping Flash buttons 1~16. The relevant
channel LED lights indicating MIDI IN
channel is set.

3)

While holding down

RECORD

, tap the

REC EXIT

button to exit MIDI setting.

Notes



This is the Channel that the controller will receive
MIDI note commands.

MIDI

NOTE

F

UNCTION

(TURN

ON/OFF)

27-69

Turn on or off program 1-48

70-93

Activate Channel 1-24

94

FULL-ON

95

DARK (momentary blackout)

96

HOLD

97

Turn on or off AUDIO

98

MODE: CHASE◄ ►SCENE

99

MODE: 1-12A_1-12B

100

MODE: 1-24A

101

Step

102

BLACKOUT

Note: When working with MIDI notes 22-93, you may simulate a fader’s increase and decrease
by adjusting the velocity of the note.

«
...
14
15
16
17
18
...
»

Содержание Stage Designer 50 TFX-48B

























Отзывы:

Нет отзывов