background image

B E F O R E   Y O U   B E G I N  

TFX-24C Users Manual Version 2.02 

5  

Before you Begin 

Unpacking Instructions 

Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that all parts are present, 
and have been received in good condition. Notify the shipper immediately and retain packing material for inspection if 
any parts appear damaged from shipping or the carton itself shows signs of mishandling. Save the carton and all packing 
materials. In the event that a fixture must be returned to the factory, it is important that the fixture be returned in the 
original factory box and packing. 

Powering 

To determine the power requirements for a particular fixture, see the label affixed to the back plate of the fixture or refer 
to the fixture’s specifications chart. A fixture’s listed current rating is its average current draw under normal conditions. 
All fixtures must be powered directly off a switched circuit and cannot be run off a rheostat (variable resistor) or dimmer 
circuit, even if the rheostat or dimmer channel is used solely for a 0% to 100% switch. Before applying power to a 
fixture, check that the source voltage matches the fixture’s requirement. All fixtures must be connected to circuits with a 
suitable Earth Ground. Check the fixture or device carefully to make sure that if a voltage selection switch exists that it is 
set to the correct line voltage you will use. 

Warnings 

 

1.

 

This product is intended for indoor use only! 

2.

 

Keep out of  the reach of  children! 

3.

 

Make sure power cord is never crimped or damaged. 

4.

 

Never disconnect power cord by pulling or tugging on the cord. 

5.

 

Always make sure that you are connecting to the proper voltage and that the line voltage you are 
connecting to is not higher than that stated on decal or rear panel of  the fixture. 

6.

 

Do not disassemble this electrical product; there are no user serviceable parts inside. 

7.

 

Always disconnect from power source before servicing or replacing fuse and be sure to replace with 
same fuse type. 

8.

 

To prevent risk of  fire or shock, do not expose fixture to rain or moisture.  

 
What is enclosed 

 

ƒ

 

Manual / Warranty Card 

ƒ

 

TFX-24CON Controller 

ƒ

 

A/C power adapter 

Содержание Stage Designer 24
























Отзывы: