Chauvet LED Techno Strobe ST-3000LED страница 5 Скачать руководство пользователя

Страница: 5 / 16

ST-3000LED User Manual

2009-12-10

14:04

DMX Channel

(Columns)

Dimmer

000~039

Strobe
Slow ~ Fast

Intensity
100% ~ 0%

Preset Programs

(1 ~ 6)

040~239

Speed
Slow ~ Fast

Sound Mode

240~255

No Function

CONTROL MODES & OPTIONS
(Rows)

For a detailed view of DMX values turn to the Appendix section in this manual. Control mode parameters are
set by DMX values in Channel # 1.

2. Introduction

EATURES

3-channel DMX-512 LED white strobe light

Blackout/static/dimmer/strobe

Adjustable flash rate, dimmer and static in stand-alone via DIP switches

Built-in automated programs via master/slave or DMX

Built-in sound activated programs via master/slave or DMX

DDITIONAL

EATURES

Linkable with LED Shadow™, LED Shadow™ 2, LED Techno Strobe™, LED Techno Strobe™ RGB, LEDsplash™ 200B
and LEDsplash™ 2 in stand alone

Additional power output: max 50 units

Includes brackets for wall and truss mounting

DMX

HANNEL

UMMARY

Содержание LED Techno Strobe ST-3000LED

















Результаты поиска

Содержание LED Techno Strobe ST-3000LED

Отзывы:

Похожие инструкции для LED Techno Strobe ST-3000LED

Бренды по названию

Популярные бренды

Chauvet LED Techno Strobe ST-3000LED, Руководство пользователя

Результаты поиска

Содержание LED Techno Strobe ST-3000LED

Отзывы:

Похожие инструкции для LED Techno Strobe ST-3000LED

Бренды по названию

Популярные бренды