background image

 

Intimidator™ 2.0 HTI User Manual 

12 

2006-10-03/14:48

 

A

PPENDIX

 

DMX Primer 

There are 512 channels in a DMX-512 connection. Channels may be assigned in any manner. A 

fixture capable of receiving DMX 512 will require one or a number of sequential channels. The user 

must assign a starting address on the fixture that indicates the first channel reserved in the controller. 

There are many different types of DMX controllable fixtures and they all may vary in the total number 

of channels required. Choosing a start address should be planned in advance. Channels should 

never overlap. If they do, this will result in erratic operation of the fixtures whose starting address is 

set incorrectly. You can however, control multiple fixtures of the same type using the same starting 

address as long as the intended result is that of unison movement or operation. In other words, the 

fixtures will be slaved together and all respond exactly the same.  

DMX fixtures are designed to receive data through a serial Daisy Chain. A Daisy Chain connection is 

where the DATA OUT of one fixture connects to the DATA IN of the next fixture. The order in which 

the fixtures are connected is not important and has no effect on how a controller communicates to 

each fixture. Use an order that provides for the easiest and most direct cabling. Connect fixtures 

using shielded two conductor twisted pair cable with three pin XLR male to female connectors. The 

shield connection is pin 1, while pin 2 is Data Negative (S-) and pin 3 is Data positive (S+). CHAUVET 

carries 3-pin XLR DMX compliant cables, DMX-10 (33’), DMX-4.5 (15’) and DMX-1.5 (5’) 

F I X T U R E   L I N K I N G  

 

 

 

 

 

Note! 

If you use a controller with a 5 pin DMX output connector, you will need to use a 5 
pin to 3 pin adapter. CHAUVET Model No: DMX5M. 
The chart below details a proper cable conversion: 
 

3 Pin to 5 Pin Conversion Chart 

Conductor 

3 Pin Female (output) 

5 Pin Male (Input) 

Ground/Shield 

Pin 1 

Pin 1 

Data ( - )signal 

Pin 2 

Pin 2 

Data ( + ) signal 

Pin 3 

Pin 3 

Do not use 

 

Do not use 

Do not use 

 

Do not use 

 

COMMON

DMX +

DMX -

INPUT

OUTPUT

3

1

3

2

1

3

2

Resistance 120 
ohm 1/4w between 
pin 2 (DMX -) and 
pin 3 (DMX +) of 
the last fixture.

Termination reduces signal errors and to 
avoid signal transmission problems and 
interference, it is always advisable to connect 
a DMX signal terminator. 

Figure 1 - DMX connector configuration 

Содержание DMX-616 Intimidator 2.0 HTI

















Отзывы: