Page 5 of 24
WELL STX 180 User Manual Rev. 1
Setup
3. Setup
AC Power
Each WELL STX 180 has an auto-ranging battery charger inside the fixture that works with an input
voltage range of 100 to 240 VAC, 50/60 Hz. To determine the power requirements for each
WELL STX 180, refer to the label affixed to the product or the
chart in this manual.
The listed current rating indicates the maximum current draw during normal operation. For more
information, download Sizing Circuit Breakers from the Chauvet website:
AC Plug
The WELL STX 180 charging case comes with a power input cord terminated with a Seetronic Powerkon
connector on one end and an Edison plug on the other end (U.S. market). If the power input cord that came
with your product has no plug, or if you need the change the plug, use the table below to wire the new plug.
Power Linking
The product supports power linking of up to 8 products at 120 V, and 11 products at 208 V and 230 V. This
product comes with a power input cord. Power-linking cables are available from Chauvet for purchase.
Battery Charge Notes
This product is equipped with a built-in rechargeable lithium-ion battery.
•
Avoid depleting the battery below 10%.
•
For best results, charge the battery in a temperature between 32 °F (0 °C) and 95 °F (35 °C).
•
When charging the battery, keep the product at least 1 m from any open flame or hot plate.
•
If the battery is completely discharged, the device cannot be turned on immediately when the charger
is connected. Allow a depleted battery to charge a few minutes before turning on the device.
•
While charging, the device may heat up. This is normal and should not affect the device’s lifespan or
performance. If the battery gets hotter than usual, the charger may stop charging.
•
When charging the battery, keep the road case’s cover open.
•
Always charge the battery with the product in an upright position.
•
Do not charge the battery for more than 24 hours.
Storage Notes
•
Store charged product(s) in a dry environment, away from direct sunlight.
•
Charge or discharge the battery to approximately 50% of capacity before storage.
•
Lithium-ion batteries continue to slowly discharge (self-discharge) when not in use or while in
storage. Routinely check the battery’s charge status.
•
Store the battery at temperatures between 41 °F and 68 °F (5 °C and 20 °C).
DMX Linking
The WELL STX 180 can be linked to a DMX controller using a wireless DMX connection. If using other
DMX-compatible products with this product, you can control each individually with a single DMX controller.
DMX Personalities
The WELL STX 180 uses a wireless DMX data connection for the
4Ch
,
15Ch
,
64Ch
, and
67Ch
DMX personalities.
•
Refer to the
chapter to learn how to configure the WELL STX 180 to work in these personalities.
•
section provides detailed information regarding the control personalities.
• Always connect the product to a protected circuit (a circuit breaker or fuse). Make sure
the product has an appropriate electrical ground to avoid the risk of electrocution or fire.
• To eliminate unnecessary wear and improve its lifespan, during periods of non-use
completely disconnect the product from power via breaker or by unplugging it.
Never connect the product to a rheostat (variable resistor) or dimmer circuit, even if the
rheostat or dimmer channel serves only as a 0 to 100% switch.
Connection
Wire (U.S.)
Wire (Europe)
Screw Color
AC Live
Black
Brown
Yellow or Brass
AC Neutral
White
Blue
Silver
AC Ground
Green/Yellow
Green/Yellow
Green
If you are not familiar with or need more information about DMX standards, Master/Slave
connectivity, or the DMX cables needed to link this product to a DMX controller, download
the DMX Primer from the Chauvet website:
Содержание Well STX 180
Страница 1: ...USER MANUAL...
