manualshive.com logo in svg

Charlton & Jenrick INFINITY 800HD BF UBL, Инструкция для пользователя, установка и обслуживание

Поделиться
Скачать
Charlton & Jenrick INFINITY 800HD BF UBL Скачать руководство пользователя страница 24

 

 

 

24 

 LT 8381 (ISS 01) 

800 HD B.F. with UBL INSTALLATION INSTRUCTION

 

 

 

 

 

 

 

 

 

 
 
 
 
 

Using 150mm core drill cut a hole following the pilot holes. Drill from the outside through to the cavity to give a good 
finish on the outside. 

•

 

Remove any cavity insulation from the cut out opening and for a further 100mm into the cavity gap each 
side and above. 

•

 

Pack “Rockwool” around the

 sides and top of the opening into the cavity for a depth of 100mm. Also put 

some behind the firebox if space is available. 

•

 

Offer the appliance into the opening and mark through the gas pipe entry hole (see connecting the gas 
supply section).  

•

 

Pass a tape measure through the core-drilled hole and record the distance from the back of the fire to the 
outside wall 

•

 

Cut the outer tube to the recorded length. Add 25mm to this measurement to determine the length of the 
inner tube and cut to size.

 NOTE: The inner tube will be 25mm longer than the outer tube

 

•

 

Remove the appliance from the opening, and position the gas supply (see connecting the gas supply later in 
this manual), taking account of the relative gas regulations regarding a gas pipe in a cavity (sleeving and 
sealing etc). Note the gas feed must be fitted with the isolation valve supplied. 

•

 

Push the appliance back into the opening and fill any space behind the appliance with “Rockwool”.

 

•

 

Complete the gas connection (see connecting the gas supply later in this manual). 

•

 

Drill the four fixing holes through the hole in the flange of the appliance and fix back using plug and screws. 

•

 

If the flue outlet is fitted below 2m from the floor or a balcony then the flue terminal guard must be fitted.

 

 

 

 

 

 

 

Packaging Check List 

 

1 x Glass Panel 

1 x Boxed Fuel Bed 

1 x Transformer Plug 

1 x Battery Holder 

1 x Emergency Power Battery Adaptor 

1 x RF Handset 

4 x AAA 1.5V Batteries 

MARKING OUT WALL FOR
CAVITY RECESSED
INSTALLATIONS

FLOOR SURFACE

CENTRE LINE OF
INSTALLATION

HEARTH SURFACE LINE
OR BASE LINE FOR 
HOLE IN WALL (150mm min. from floor)

MARK POSITION
OF LINTEL

605.00

490.00

 

861 

FLUE 

CENTRE 

 

1030 

LINTEL 

HEIGHT 

BASE OF OPENING 

 

Содержание INFINITY 800HD BF UBL













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды